2 Results: New & Used in Engine, Engine Parts & Transmission in East Ipswich 4305, QLD

DRIVE SHAFTS OFF THE REAR OF AN EARLY LOTUS ELAN BUILT IN THE 1960s. THEY ARE IN GOOD CONDITION. ITEM CAN BE PICKED UP IN IPSWICH OR CAN BE POSTED AT BUYERS EXPENSE.

I PUT THIS IN MY CORTINA RACE CAR AND IT WAS TO SAVAGE WHEN YOU TOOK YOUR FOOT OFF THE CLUTCH. i TOOK IT OUT AFTER ONE RACE. CAN BE PICKED UP IN IPSWICH OR I CAN SEND WITH AUST POST AT BUYERS EXPENSE.

I HAD THIS SOLID CENTRE CLUTCH PLATE MADE A FEW YEARS AGO AND NEVER GOT AROUND TO USING IT. BRAND NEW NEVER USED. CAN BE PICKED UP IN IPSWICH OR I CAN SEND WITH AUST POST AT BUYERS EXPENSE. HAVE PLENTY OF ENGINES PARTS AND GEARBOXS AVAILABLE.

BRACKET HAS HAD THE HEADS OF THE BOLTS WELDED TO MAKE IT EASIER TO BOLT IN TO THE CAR. THIS BRACKET SUITS THE ORIGINAL GIRLING BRAKE BOOSTER. IN EXCELLANT CONDITION FOR A 50 YEAR OLD PART. CAN BE PICKED UP IN IPSWICH OR SENT WITH AUST POST AT BUYERS EXPENSE.

THIS CROSSMEMBER HAS HAD A RUSTED IN BOLT ON ONE END TO HOLD THE LOWER CONTROL ARM ON. IT HAS BEEN BASHED OUT OF SHAPE TRYING TO GET IT OUT. CHECK THE PICTURE YOU WILL SEE THE ENLARGENDED HOLE AND THE TWISTED FRAME. IT REQUIRES HEATING UP WITH A OXY AND STRAIGHTENING BEFORE YOU CAN USE IT. NORMALLY SELL FOR ABOUT $400 IN GOOD CONDITION. CANBE BE SENT WITH AUST POST OR PAC AND SEND AT BUYERS COST.

THIS CAM HAS A BIT OF WEAR ON A COUPLE OF THE LOBES BUT IS STILL VERY USABLE. HAS ABOUT .380 LIFT ON THE LOBES. WOULD SUIT A CAR THAT HAS A MILD TUNE. IT HAS 293 STAMPED ON ONE END. CAN BE PICKED UP IN IPSWICH OR SENT WITH AUST POST AT BUYERS EXPENSE.

THIS IS A FACTORY SUPPLIED ITEM. MOST CORTINA GUYS NEVER KNEW IT WAS FITTED TO THE AUSTRALIAN GTs. ALL AUSTRALIAN MK1 GT AND GT 500 CORTINAS HAD THIS FITTED ON TOP OF THE TUNNELL UNDER THE CARPET TO HOLD THE CARPET UP TO THE CONSOLE. THE LOTUS AND OTHER ENGLISH CORTINAS HAVE A DIFFERENT FLOOR PAN AND TUNNELL THAT HAS A LUMP IN THE METAL FLOOR THAT FILLS THE GAP UNDER THE CONSOLE. IF YOU HAVE AN AUSTRALIAN GT WITHOUT THIS FIBREGLASS PART FITTED THE CARPET WILL SAG DOWN AND YOU CAN PUT YOUR HAND

THE GEAR LEVER WILL FIT ANY MK1 CORTINA WITH A MANUAL GEARBOX. THESE ARE A BIT HARD TO FIND THESE DAYS. I HAVE PULLED IT APART AND REPLACED THE NYLON PIVOT BALL WITH A STEEL ITEM. ALL BUSHES AND REVERSE PLATE CHECKED AND IN EXCELLANT CONDITION. THE GEAR LEVER HAS HAD A PIECE OF METAL WELDED IN TO EXTENT THE LENGTH ABOUT 40MM. CAN BE PICKED UP IN IPSWICH OR SENT AT BUYS EXPENSE WITH AUSTRALIA POST . I ESTIMATE THE FREIGHT TO BE BETWEEN $25 TO $30.

THESE ARE THE ORIGINAL PLATES THAT CAME OUT ON THE ENGINES WHEN NEW. A RUBBER O RING ON EITHER SIDE TO SEAL. GO BETWEEN THE WEBER CARBIES AND THE LOTUS HEAD. CAN BE PICKED UP IN IPSWICH OR SENT AT BUYERS EXPENSE WITH AUST POST.

FITS ALL MK2 GTS FROM 1968 TO 1971. SOME CORRISION ON THE FRONT WHERE THE WATER GOES THROUGH THE MANIFOLD BUT OTHERWISE IN EXCELLANT CONDITION. WILL ALSO BOLT ON TO 1300 AND 1600 ESCORTS MOTORS. CAN BE SENT WITH AUST POST AT BUYERS EXPENSE OR PICKED UP IN IPSWICH. GARRY click to reveal