TopMarch Special : VE 6.0 Litre Engine V8 Complete Suit Conversion .
March Special : VE 6.0 Litre Engine V8 Complete Suit Conversion .
TopMarch Special : VE 6.0 Litre Engine V8 Complete Suit Conversion .
March Special : VE 6.0 Litre Engine V8 Complete Suit Conversion .
27/03/2024
TopMarch Special : BA 5.4 Litre Engine V8 Complete Suit Conversion .
Easter Special. BA - BF 5.4 Litre Engine V8 Complete Suit Conversion .
28/03/2024
Cam plates
Ford six cylinder cam plates. Each $10. Can post fir $5.
06/10/2023
Intake block plate
Ford big block and XW/XY Cleveland intake block plate. Payment in person or bank transfer, can help wrap up for your post
30/09/2023
Turbosmart diaphragm
Turbosmart diaphragm TS******2001 brand new never opened phone or txt pick up only
26/01/2023
Holley 650 Quadrajet 6210-3
Have a full rebuilt Holley 650 cfm 4 barrel double pumper Quadrajet spread-bore. Front metering block is 8522/L62103/8521, rear metering block is 7832/70021. Listed vin code 6210-3-1881. Missing rear kick down lever. Payment in person or bank transfer, can help wrap up for postage, thanks
04/10/2022
FE 428 complete motor
Ford 428 Service block bored to 4.13 ( standard), date code 1L20, PI heads C8AE-PI fully reco’d, 16 hole exhaust set up, 428 SCJ pistons, C7AE rods, Edlebrock street master alloy intake, hi volume fuel pump, crank is 1UB at 10/10 machined , Howard hydraulic cam 525/525 lift at 267/277’on 108’, heads date codes are 9G15/9H7, high volume oil pump. Because of the lowered price all these extra items will not be on this motor when sold , there either extra payment or sold individually on my other si
02/10/2022
64 pairs3/8, 10 degree coletts
Carbon Steel valve coletts 3/8 at 10 degree, single groove, 64 pairs in bag all new and NOT used. Can post or can be picked , payment on pickup or bank transfer, thanks
13/03/2022
Holley Dominator 1050
Holley 1050 Dominator double pumper, rebuilt last year then sat on shelf in garage. Was used on fresh water speed boat. Owner has cleaned his home out and moved back south into NSW. Will need another clean up due being out a swap meets. Payment in person or bank transfer, can help wrap up for postage, thanks
05/02/2022
Ford 6, 302w,351w,351c,428 oil drive shafts
I have 2 Ford 6 cylinder oil drive shafts in fairly good shape. The are $5 each Can post off if you wish to pay for service. Also have new unused heavy duty Cleveland,Windsor both 351 and 302/289 shafts each are $50. FE 390/428 oil shafts $55. Payment in person or bank transfer, thanks
09/12/2021
750,800,830,850,780 Holley Carbies
Have 800DP- *****6514 and 6514 metering blocks, 830DP- *****1173 and 5925 metering blocks, all are mechanical 4 barrel Holleys. Holley 3310-2- 750 vac secondary, prices start from 375 up to 500. Have refurbished 780 cfm Holley’s vacuum secondary $500. Payment in person or bank transfer, can help wrap up and post off, thanks
08/11/2021
Cleveland Cast Exhaust Manifolds
We have a set of Cleveland 2V cast exhaust manifolds, these have been chemically cleaned, no cracks and still have the original heater pipes installed, you can clearly see date codes and cast codes price is $175. Also have other sets for $100 chemically cleaned and painted or single’s for $50. Payment on pickup or bank transfer.
03/11/2021
71/73 Mustang Radiator
2 core copper 71/73 mustang radiator with 3 /4 core frame tanks. This core unit can be used to enlarged and recored to suit our Australian heat. Could use a flush out, $45. Will fit other Ford's V8. All so front air conditioner condenser with filter canister and a hose, still good condition also with mounting frames $100. Payment in person or bank transfer. Can wrap up for couriers. Thanks
06/10/2021
Spring seats
I have a number of spring new seats, the part number is on the items for sale.Pricing starts off at $50 up to $75. Crowder 68955, 1.745 x 1.63/0.635" cups. Crower 68940, 1.56x0.740/ 0.562", seat docs. Payment in person or bank transfer, thanks
28/09/2021
New heavy duty valve springs
Heavy duty dual valve springs to suit roller cams and remove inner spring to suit 600 lift solid cam's. Isky racing cams, 1.56 OD, 0.74" ID, seat 680 max lift, 1.19" col bind, dual spring, these springs have been run in on testing circuit or dyno. Payment in person or bank transfer, thanks Also have new Windsor small springs, chev, Holden, Chrysler type springs, Ford 8/6 cylinder Barra motors. Springs in many sizes and up to 800 lift cams.
28/09/2021
XW/XY/XA/XB Steering Box’s
XY/XW 20 to 1 ratio steering gearbox, was spare for my XY sedan. No leaks and good to turn and return to neutral position. Payment in person or bank transfer. Can help wrap up and post.
05/09/2021
302 /351 Windsor Rods
I have 7 of 302 Windsor rods F2TE-BA 7x 302 5 litre used rods $50. These sets have been used in standard bore motors. Also have a full set of good 351 W rods $180. Payment in person or bank transfer, can help wrap up ready for postage. Thanks
02/09/2021
New Nissan speedo Drive
I have manual / automatic gearbox electronic speed drive to suit Nissan vehicles. All new and imported from US due to non stock from Nissan Service Departments in Australia. It has a long shaft drive. Payment in person or bank transfer. Can help send off, thanks
26/07/2021
Windsor roller rockers
I have a number of Windsor roller rockers and stud kits, range from 300 to $375. Payment in person or bank transfer, can wrap up for postage. Factory rockers both in pressed steel of casted. Alloy 7/16 set used $200. Thanks
20/07/2021
302 Windsor Crank
This is a standard 302 Windsor crank 2M, yes it was in a running engine but was stripped for stroker input. It has been mic'd and was still in zero measurements allowance and then stored . Yes it is standard. Payment on pickup or bank transfer, can help wrap up for couriers, cheers
20/07/2021
428 FE Cobra Jet Heads
I have a number of FORD FE 428 Cobra Jet heads, starting off at $2500 bare or complete $3500. Some have been done up but will need a clean as from sitting in shed even being wrapped, there are no problems with these heads, different years. Also there are alot of other FE parts for sale. Can help put on courier to send off. Payment in person or bank transfer, thanks
14/07/2021
FE 428 Alloy Covers
I have a set of Ford 428FE tall Ansen alloy tapper covers unused, found these covers sitting around in boxes while cleaning out shed. Will fit 390, 427 and 428 FE motors. Can help send off by post. Payment in person or bank transfer, thanks
11/07/2021
Ford 9" Trac-Lock Gears
Have a new Ford 9" Traction Lock Yukon Grizzly 31 spline centre, YDGF9-31-AG, 26009 DJB. Still in orginal box made in the USA, comes with complete bearing kit and seals. Can help wrap up and post, payment in person or bank transfer, thanks
24/06/2021
Windsor Harmonic Balancers
I have a number of Windsor Crank Balancers, new and used. 289, 302 to 351 and strokers. 28 oz to 50 oz units. The two end balances (black and silver are new but painted to stop surface rust) are $175. , also new 50oz chrome SFI . Standard balancers 28 oz $75 in good condition. Payment in person or bank transfer, can help post off, thanks
13/06/2021
Jesel Roller Tappets
Jesel Roller Tappets new in dirty boxes, the diameter sizes are 0.905" and 0.937". Can machine your block to use, great for Roller cams. Can help post off, payment in person or bank transfer, thanks
13/06/2021
CARRILLO RODS
I have a number of complete sets of CARRILLO high performance H beam rods, used only once on a 500 mile circuit race or DYNO time set up or have been assembled on pistons then removed. I have different lenghts etc. All in top shape with codes and sizing set up on rods, CR codes from Carrillo. The Rod end measures are with out bearing size, just the open diameter, these sizes can be machined out for larger bearing sizes. Only one set is missing rod bolts. ITEMS 34 & 35 are 6 inch long, 1.953" ro
12/06/2021