19 Results: New & Used in Engine, Engine Parts & Transmission in Queanbeyan 2620, ACT

For sale Edelbrock Super Victor EFI intake manifold for BB Chev tall deck Part #29165 Manifold comes complete with Edelbrock fuel rails Part #3533 All coated in black AN20 fitting for water line Can post at buyers expense

Main gasket removed from package to check fitment but never installed. This gasket kit was purchased for a Lexus IS250 but did not fit since the valve cover is different on this engine compared to other Toyota and Lexus 2GR based V6s due to the high pressure fuel pump. I needed a gasket that had an extra shape and length at the back of the valve cover. Check the photos carefully for the shape of this gasket, message me for further details if you are unsure. The package has been opened however t

HOLDEN HR HK HT HG HJ HX HZ,SIX CYLINDER RED MOTOR CLUTCH PRESSURE PLATE.

B&M 70360 Shift Improver Kit for Automatic Transmissions

30mm / 32mm pipe adapter with temperature sensor port / car for a coolant pipe or any pipe Joiner With a thermostat temperature port for a sensor 2 sizes Let me know if interested

Genuine Toyota Oil Filter PRADO CAMRY HIACE HILUX KLUGER ENGINE APPLICATION • 1G series • M series • MZ series • VZ series • 22R series • 3S-GTE(CELICA ST165 only) • JZ series • 2T7-FF

NEW NEVER FITTED… Completed front drive shaft with both CV joints. NEW part, never fitted to car. Car sold before part arrived. RH C V joint for Hyundai Getz 2015. Can be bought direct from trade for over $200.00 I’m only asking $50:00. It’s an absolute bargain !

If it’s listed it’s available! Toyota 4A 2A original air cleaner Believe it’s off an 84 Corolla See photos for best description

If it’s listed it’s available! Toyota 4A head and extra bits Unknown condition Believe it’s off a 1984 Corolla A few extra bits Dipstick, Pistons and some other bits See photos for best description

Off a Holden 330ci Went with a different set up now Never had a problem Car ran beautifully Great condition Comes with pressure gauge and aeroflow fittings as seen

I have a 2012 Volvo XC60 diesel motor with 151,000 klm and a gearbox with 77,000klm on it for sale, as it couldn't be installed into my car. All the seals were replaced in the gearbox for just for good measure, because I was intending to keep the XC for a long time. The motor has been professionally assembled to the gearbox and as you can observe from the photos, the mechanics took great care when packing the engine. The engine controller is still attached to the wiring loom. The motor is i

extractors ? Brand new never used I think these are for a Suzuki sierra $165 Cheers Luke

Original cast steel cylinder bracket with bolts. Suits all Holden 6 and 8 cylinder bell housings. 3 and 4 speeds. Not Aluminium. Very good condition. Pick up Queanbeyan.

Toyota MR2 sw20 / Glove box Gauge Pod / 4x SAAS Gauges Hello , For sale I have this pod that was custom built to fit into a MR2 glove box perfectly. The metal has been nicely cut and bent u see angles, It’s a perfect fit and allows you to mount 4 gauges It has 4 SAAS units but they do not have any sensors… You can still buy them and then use them.. Happy to sell the gauges for a bit extra or separately. let me know!

K&N air filter / 4” 3.” 3.5” adapters / pod filter / Made in USA Has been washed and cleaned Ready for use Able to fit 3 sizes comes with rubber adapters

Thermo fans / For project / Hello, Selling a variety of thermo fans. From a various automotive projects. Let me know what you are interested in! Many thanks.

*****1960 / Chevrolet Front Fan shroud / Chevy Impala , Belair / Metal Original part from a 1959 Chevrolet Impala. Suits GM bodies 58-61 up toI think Metal fan shroud Hard to find these days... Can post if needed.

Holden NOS, EH179, HD, HR, HK 3 SPEED crash box 1st/reverse slider gear New in box, part no. 7421591 Price reduced from $220 down to $210 posted. A few available. Phone Peter on .

Got it for a project car Great intercooler in good condition Ready to use