2003 mercury outboard motor
Perfect runner pumps plenty of water
Water pump replaced about 6 months ago
Comes with fuel tank, fuel hose and cover
Stand not included
Selling on behalf of a Freind I have test started and run the motor before listing it to make sure it was in goo...d working order
Rear boat loader with storage cage.This is on my 100 seriers land crusier
This is on my stanard roof racks As you can see the pic of cage this will also suit a car without or with gutter all you have to do is weld the sides for gutters back on I have the gutter clips as well.
The rear boat loader ...is complete with a both remote and manual operation and has winch
and all ropes clips and is in good working order and can be picked up from either Brisbane
or coffs harbour
for enquiries ph ...show more
Stainless steel prop. Outboard is in good condition and currently still on the boat for next 2 wks if you want to see running. Can have it lifted straight into your vehicle at time of removal. Viewing available after 5pm weekdays and all weekend by appt only.
This motor is in very good condition. It is no longer needed. We have had our fun, now it's time for someone else to enjoy.
This motor was bought new on 30/11/2013. Normal retail price over $300.
It pushes a 12ft tinny along at a fast walking pace with ease.
***PLUS AS A BONUS.....WE'LL ...THROUGH IN A SPARE PROP......RRP $20.00***
Can deliver to Sunshine Coast or Gympie for a small fee.
For those into the technical information:
Model: Venom SXW 54/26
Thrust: 54lb ...show more
6 horsepower evinrude. Never used by myself and bought off a friends friend who came from country victoria and had said it was only used in fresh water. Didn't start when i sold the boat to my mate so i kept it then got it serviced with new head gasket and impeller which now makes it run like a drea...m. price is negotiable as it will probably need a service soon as it has not been run in the last year untill i started today. Will need a new hose for water to pump out of engine as it currently ...show more
Boat moulds. Full set of moulds to build a purpose designed 7.6m fishing boat as shown in pictures. Has full length 1.9m sleeping area in cabin. Huge cockpit. Large under floor fish keeper and storage compartments. Moulded sink and room for 12 volt fridge if required. Fibreglass stringer system unde...rfloor so will never rot. One pice fully moulded fibregllass floor. Easily does forty knots with 170hp motor which gives great economy. Renown hull design. Heaps of internal moulds included - not ...show more
Near new F150AETL 20inch(long shaft Four Stroke outboard motor with only 36hr of fresh water use only. Great condition and very well maintained - like new! Comes with All lan guage (taco, speedo, fuel management) and 703 control box. Reluctant sale.
Long shaft model 25 DML single carburettor. Very well maintained and reliable. Currently set up on forward control 4m runabout. Can be seen running and happy to demonstrate on the water to seriously interested buyer. Tiller throttle disconnected. Owner upgrading.
I urgently need to sell this motor it is in perfect condition and looks good,it cost $2850 when new and would cost $900 plus if purchased of a dealer,just been serviced and comes with New Tank and Line, Photos can be sent by Phone as I do not Know how to put them on this add. Must be sold within 2 d...ays.show more
The Ultimate winch for anchor retrival is this used Stress Free Maxi anchor winch it comes with every thing you need to install it on your boat.It comes with 30 metres of rope with 10 metres of chain,switch for up and down,replay,two power lead one at 6 metres and one at 2.7 metres,two earth leads o...ne at 7.5 metres and one at 2.7 metres.I have pulled it out of a 6.5 metre Kevlacat.show more
2 IGNITION SWITCHES AVAILABLE
3 Position - Off/Ignition/Ign - Start
Coded tumbler lock and key - spring return
12 Amperage ratings at 12V - 10A Ignition - 5A Start - 1A Choke
All Brass and Bronze with resin base
Perfect Marine Application
13/16"-24 thread and 20.63mm diameter
Mount...ing Stem: 30.95mm Long (26mm to face nut)
Suits Panel Thickness 1.52mm to 25.40mm
Dimensions: 74.17mm x 36.58mmshow more