GM Part No 12621258 ( AC Delco Part No. 41-110)
Set of 8 Iridium Genuine GM Spark Plugs
These are the exact same as if you were to walk into Holden and purchase them for RRP $43.50 per plug or $348 per set.
The best Spark Plug currently available for your V8.
Iridium Technology (better t...han platinum), 160 000km Lifespan. Smaller, more efficient, Iridium electrode designs improve cold starting, quicker acceleration, and lifespan. Iridium plugs require reduced ignition system voltage ...show more
GENUINE TIAL Sport 38mm V-band wastegate
MADE IN U.S.A
Part Number: MV-S
Brand new in box.
Each unit comes with its individualized serial number.
347 Stainless Steel Alloy is used for valve and valve housing.
High temperature silicone Nomex reinforced actuator diaphragm.
17-7... PH Stainless Steel actuator spring gives consistent pressure at high temperature, resists "relaxing" at temperature to 900F (483C).
Nitronic 60 Stainless Steel is used for the valve seat, and valve ...show more
up for sale is a VX Getrag manual conversion for commodore
Car shifted well before it was removed and the kit is complete with all u need to bolt into your vx shape commodore. will fit other models with modifications tho.
Can come with the ecotec engine at extra cost ($300) or i will seperate ...the 2
Also have a T5 gearbox here $150 from a VR commodore
And a 4L60e from an LS1 Vx commodore with converter for $400show more
I bought this to use some parts on my car but now im selling all parts, please call if interested in ******8482 ill give you the cheapest price.
- gearbox and transmission with sports mode manual shift
- full gas setup
- all 4 doors
- computer & keys
- back seats only
For Sale is a standard 302 cubic inch Ford Windsor motor.
Removed from a Falcon Panel Van in about 1983 and was still running ok without smoke.
No gearbox, flywheel, pressure plate, clutch, or starter motor included. Exhaust manifolds to be removed at time of sale and not included either.
...Motor turns over manually.
First photo taken today, 2 & 3 about 3 years ago, and 4th in 1987. It has always been stored in my garage since 1983, very low mileage, just dusty. No reason that it ...show more
I have this bell housing taking up space and i dont need it. I think its grey motor but not sure. Cant think of anything else it could be for. If you have 1 you will know. It has mounts attached to it and its alloy. clutch fork etc is there. Its got to be cheap at this price, just want to clear out ...everything I dont need.show more
For sale: extreme clutch hd. Didn't slip or shudder when removed from sr20det: $100
180sx rear camber arms: $10
180sx front castor arms: $10
Two sets of 180sx rear pads, unsure of brand, heaps of meat left on them. $20 a pair.
Located in Kingston area
partin out my running gear Consists of a s15 motor wit loom bottom end needs rebuild.. I have a custom built inlet manifold that holds a top feed fuel rail wit 850cc injectors this unit is direct bolt on all hard work is done.. I have a 5 speed gear box wit a good clutch tail shaft power fc and hand... controller obviously anything to do wit the running gear will be gettin sold msg me to see I have wat your after contact me on ******5739 show more
all parts are s13 sr20det unless otherwise stated
alternator with bracket- $60
power steering pump with bracket- $80
inlet manifold with water lines and IAC - $50
flywheel needs machine - $50
starter motor - $60
sr20de non turbo lukey extractors with o2 sensor- $80
s15 480cc injectors - $20...0
rocker cover needs a coat of paint $50
clutch fan $40
s13 redtop sr20det long motor, no accessories. only started once to find it had no oil pressure and knocking. $350
crank angle sensor ...show more
Brand new set of pistons only 50$ . these are so cheap. I will not freight! PICK UP ONLY. Price has been reduced heavily. Actually tired of getting freight quotes for people so want these gone. These will be great to freshen up a standard motor. These will go good in a cruzer and they are cheap.
I... have had a few silly questions. they are priced to sell. 1st in gets them.show more
please note, this motor needs a rebuild, it ran with good oil pressure and the head is clean, but at the very least it will need new bearings. personally i would strip it and inspect the crank for damage.
s13 blacktop sr20det, with inlet manifold, injectors, alternator, flywheel... and engine mounts,
stock turbo with lines and dump pipe on an aftermarket low mount manifold.
5spd gearbox with fork and a good throwout bearing
basically everything needed ...show more
Hi for sale is a good working order trimatic auto. Was removed from car about 6 years ago and was running fine. Minus torque converter. clean looking with no sludge hanging around. Happy to answer any questions!