For Sale Holden Commodore 4speed Automatic 4L60E/T700 to suit VN-VZ 6Cyl or V8
I Am Offering Repaired or Reconditioned Automatic Transmission in Either Standard or Performance Options
OPTION 1 - Minor Rebuild
What You Get:
Auto is Fully Stripped, Cleaned and Reassembled with The Following Parts.
-Gasket, Seal And Ring Kit
-New 2-4 Band
-Pump, Front and Rear Stator and Case Bushes
-Moulded Piston Kit
-Accumulator Pistons as Required
SE Qld Nissan CUBE & Micra owners
LOW KLM CR14DE Motor
Nissan CR14DE long motor from a 2010 Nissan Micra with a low 6000Kms.
This motor was purchased in August 2011 and has been oil filled (stops bore corrosion) and fully sealed until today.
As you can see in the pictures it has been unwrapped and unsealed for the listing pictures today (16/11/13).
It is a long motor and has the flywheel & water pump and it complete to the coil packs.
I bought this motor as a spare in case my ...
Up for sale is my 20" Rims. Only issue is the clear coat is slightly coming off but you dont really notice it.
Nitto Innvo Tyres, 2 are great tred, 2 need replacing.
Comes with 4 Spare achillies with about 85% tred and 2 street slick Nitto NT05's
Engine built in 2009 for a project that never ended up happening. Has only been run for 15mins the Cam still hasn't been run in. Basically a new engine! Full receipt history for almost $10K in parts and labour.
Holden 308 Black Block
Scat cast crank
Scat i-beam rods
650 Holley DP
Harrop dual plane manifold
Engineered VN Cast iron heads
All Egineering works done by Chris Milton engineering. Video of first startup apon request.
New master and slave cylinder! Fit approximately xw through xd ect? The Master is full alloy and the fill up point stands straight up! Ring for details and photos!!!!! I can provide purchase receipt, Selling half price!
as new 350 Holley bolted to a John Cain performance manifold to suite any old Holden straight six, 202,186,173,red,blue etc, installed in car to get a bit more stick but turns out engine was worn and couldn't handle the extra fuel so off it came, car is gone at a loss just wanna recover a few bucks, also comes with reducers, and some older Holley parts I have from a previous can of rust!, can courier if needed at buyers expense, call Mark- 041431****
2 Inch Pipe Lukey Performance Exhausts. Sound absolutely cracker. These are straight through.There are 2 available. Were used on a 351 that tore shreds off ears.... $80 for 1 or both for $140. New price is around $140 ea.
*NOTE can post Auswide*
"T" Bar SHIFTER Assembly, ex Holden Commodore VP, as in pic, in good used condition, was working OK when removed from donor engine & been sitting in the shed for couple of years, No damage. Suit rodder or car rebuild.
Can post Auswide, ie $17 Auswide ex Adel, would be cheaper to local postcode. Local pick up, COD in TTG area is OK.
Terrain Tamer Radiator and Heater Hose Kits to suit Toyota Landcruiser HZJ70/73/75. Leading brand renowned for quality 4wd products. Retailed for $63 (Heater Kit) and $37 (Radiator Kit) respectively. Selling both for the cheap cheap price of $60.
Chasing a running engine or good condition cylinder head for a m40b18 4cyl 318i. Also need good condition plastic bumpers and glovebox lid/latch. Would consider a whole parts car if the price is right. Please call or text only.
It is my nissan micras engine with very low kilometers only 65000 ks done the model is 2010 my care crashed so I took out the engine and want too sell it so if you are interested in an low kilometers engine this would be an perfect engine for your little car
Nissan L26 Engine with mild cam, starter motor, alternator, triple Mikuni/Solex 40mm side draft carburettors with linkages, 280zx manual 5 speed gearbox with clutch fitted. The engine and gearbox were removed from a Datsun 240z last weekend and is in excellent condition and perfect working order. Inspections are welcome. Prefer to sell as a complete unit.
The engine will fit into a Datsun 240z, 260z, 280zx, early Patrol, early Skylines, 240k, 260c and 280c etc.
I have other parts available. ...