327 engine block, has beeen rebuilt and comes with crank rods and pistons, that are still in engine and in perfect condition, pistons are 0.030 oversize , is a genuine 1967 block with cast numbers GM3903352, i was happy with motor it ran well--glenn
ford 1600 x flow short motor this is one of the 4 xxxx blocks very hard to come by - this short motor is fully balanced ARP rod bolts shot peened rods, performanced cam, new rings and bearings, bores honed and block decked - this is a quality short motor professionally re built by race engine builde...rs. Invoice for work done supplied. fit cortina or escortshow more
TOYOTA HILUX KUN26 4WD GEARBOX FULLY REBUILT AND STRENGHTENED FROM FRONT TO BACK ! GEARBOX COMES WITH A 6MTH / 20,000 KLM WARRANTY.
AUSTRALIA WIDE SHIPPING AVAILABLE ON ALL OUR TRANSMISSIONS.
FOR MORE INFO PLEASE CALL US ON 0 OR ON THE INTERNET AT :
This is an Isuzu G200 2 litre which i had rebuilt for my gemini , which is now sold.
It was a low mileage engine. It has been bored out one mm ( 25thou.) and fitted with quality (Hypereutectic ) pistons.
New rings , bearings ( crank ground 10 thou on mains and big ends)
Rods resized , new b...olts etc.
Block hot tanked, pressure tested and line honed.
New timing chain set , oil pump and complete gasket set supplied.
All work professionally done several weeks ago and receipts ...show more
V6 supercharged eco tec engine.
From Holden vx commodore.
I got the engine for a project car but have no time. I have never had engine running in car.
TEXT !!!! 0
Pick up Clayton or can deliver for a fee.
Rebuild kit for Yanmar 3TNE84 Komatsu 3D84-3 Engines
and Full gasket Set
Liners are also available but not included in this package.
Komatsu PC25 PC27R PC30MR PC35R PC38UU Mini Excavator and Komatsu WA40-2 Wheel Loader
2 x COMPLETE MACK 470 HORSEPOWER E7 CCRS MOTORS AVAILABLE FOR PARTS.
BLOCKS, HEADS, CAMS, CRANKS, RODS, TURBOS, etc, parts to suit E-TECH engines 1998 to 2002 and CCRS 2002-2007
HEADS $1,200.00 each 4 available
470hp Turbo with waste gate $2,000.00
Camshafts with all roller lifters an...d EUP roller lifters $2,000.00 a set
CCRS complete engine harness $1,000.00
EUP PUMPS $300 each
Engine blocks and rods
Starters, Alternators, flywheels, Flywheel housings and All other parts also ...show more
Up for sale is my Mazda 6/3 MPS top mount intercooler
It's the standard intercooler semi polished but fits the mazda 6 MPS as mazda 3 MPS
Need it gone no longer own the car and it's just sitting around
tryed installing it but didnt know what i was doing, brand new unit. priced for a quick sale
The all-new MSD Transmission Controller was developed completely in-house – evolving from the engineering expertise and proven performance of our Atomic EFI technology. In fact, the Atomic TCM is designed... to integrate directly with the Atomic EFI when using Brainwave so you can modify transmission operation parameters from the same handheld monitor! Doing away with the need for sensor duplication, ...show more
308/304 vk v8 done up for lh torana but I want to go bigger it has chrome torana sump chrome rocket covers torcher inlet manifold electronic distributor 650 holley all in good condition motor had only done under 80000 kilometers as I was told when I bought it
Give you accurate readings for finding faults in valves, piston rings, cylinder bores or head gaskets
Fit for petrol engines on Cars, Motorbikes, Trucks and petrol vehicles
Contains gauge(psi/bar) x 1 , extension x 1, Straight & Angled Push-On
Gauge Diameter approx... 60mm
Gauge Type Dual scale, psi/bar
Gauge Range 0-300psi & 0-20kg/cm2
Extension length approx 520mm
Thread sizes Adapters M8 X 1.5, M10 X 1.0, M12 X 1.25, M14 X 1.25
USED ONCE AND ...show more
Used for 6 months in my 300tdi. All fins straight, bit of external road grungle on the tanks and such but Excellent condition otherwise. I have flushed the internals so its ready to install. Removing due to selling vehicle. 6 months use, about 10,000km.
A quality unit that can improve performanc...e of any 300tdi up to 20% according to the manufacturer and I found this to be accurate, really helping with EGT's and performance.
Will fit both Discovery & Defender models.
Will ship Aus ...show more
Suitable for the replacement of valve spring and valve stem oil seal without the need to remove the cylinder head.
Application : Opel/Astra, BMW, Seat, VW, Audi, Hyundai, Toyota, Ford 16V, Runatle 19 and Clio.
Many other models, Very universal
Used once and reboxed.
1x used, oil line banjo bolt to suit Mazda FD RX7.
2x used, copper washers to suit this bolt.
Came off a Series 8 FD3S 13B engine, unsure if it will suit an earlier version of the motor, EG: FC3S / FC RX7
The bolt head does have a little bit of rounding, but it isn't serious.