ford 1600 x flow short motor this is one of the 4 xxxx blocks very hard to come by - this short motor is fully balanced ARP rod bolts shot peened rods, performanced cam, new rings and bearings, bores honed and block decked - this is a quality short motor professionally re built by race engine builde...rs. Invoice for work done supplied. fit cortina or escortshow more
TOYOTA HILUX KUN26 4WD GEARBOX FULLY REBUILT AND STRENGHTENED FROM FRONT TO BACK ! GEARBOX COMES WITH A 6MTH / 20,000 KLM WARRANTY.
AUSTRALIA WIDE SHIPPING AVAILABLE ON ALL OUR TRANSMISSIONS.
FOR MORE INFO PLEASE CALL US ON 0 OR ON THE INTERNET AT :
This is an Isuzu G200 2 litre which i had rebuilt for my gemini , which is now sold.
It was a low mileage engine. It has been bored out one mm ( 25thou.) and fitted with quality (Hypereutectic ) pistons.
New rings , bearings ( crank ground 10 thou on mains and big ends)
Rods resized , new b...olts etc.
Block hot tanked, pressure tested and line honed.
New timing chain set , oil pump and complete gasket set supplied.
All work professionally done several weeks ago and receipts ...show more
Give you accurate readings for finding faults in valves, piston rings, cylinder bores or head gaskets
Fit for petrol engines on Cars, Motorbikes, Trucks and petrol vehicles
Contains gauge(psi/bar) x 1 , extension x 1, Straight & Angled Push-On
Gauge Diameter approx... 60mm
Gauge Type Dual scale, psi/bar
Gauge Range 0-300psi & 0-20kg/cm2
Extension length approx 520mm
Thread sizes Adapters M8 X 1.5, M10 X 1.0, M12 X 1.25, M14 X 1.25
USED ONCE AND ...show more
Used for 6 months in my 300tdi. All fins straight, bit of external road grungle on the tanks and such but Excellent condition otherwise. I have flushed the internals so its ready to install. Removing due to selling vehicle. 6 months use, about 10,000km.
A quality unit that can improve performanc...e of any 300tdi up to 20% according to the manufacturer and I found this to be accurate, really helping with EGT's and performance.
Will fit both Discovery & Defender models.
Will ship Aus ...show more
Suitable for the replacement of valve spring and valve stem oil seal without the need to remove the cylinder head.
Application : Opel/Astra, BMW, Seat, VW, Audi, Hyundai, Toyota, Ford 16V, Runatle 19 and Clio.
Many other models, Very universal
Used once and reboxed.
1x used, oil line banjo bolt to suit Mazda FD RX7.
2x used, copper washers to suit this bolt.
Came off a Series 8 FD3S 13B engine, unsure if it will suit an earlier version of the motor, EG: FC3S / FC RX7
The bolt head does have a little bit of rounding, but it isn't serious.
Have for sale a pair of toyota ct12a turbos which came standard on the 1jzgte engine
Were removed from my soarer at 90,000ks when I went single and have sat in the shed since.
Didn't blow any smoke
Please message me as have trouble receiving phone Calls. Thanks
Nissan SR20DET removed from my 180sx due to car been taken off the road runs great comp test welcome. Has nismo 740cc injectors and brand new engine mounts, comes complete minus turbo and manifold
Hi I have a 1977 Porsche 911 in need of a new motor or Crankcase as the head studs are pulled and case savers have failed. I am after either the 3.2 ltr the 3ltr or the 2.7 as any of these Porsche engines will suit. Please don't contact me if you are wanting to purchase the vehicle as its not for sa...le