121 views
Fencing trailer
Fencing trailer
4.2m x 2.4m flat top trailer
Built in 2020
Ladder rack
Ringlock arms to suit both 500m and 200m rolls
50mm RHS under trailer on 45 degree to straighten bent star posts if needed. Have never needed to do it.
Chequer plate on pull to sit wire spinners on or either put them on back of Ute
Arm to suit spring balancer and Marchant/Christie post driver
Rear Hayes trailer pull
3.5t simplicity suspension. Was designed with a load sharing suspension to be able to let tyres down and use in wet weather with snow chains. Haven’t actually tried it though.
Fits maxi posts and normal posts
Note doesn’t come with post racks. Can easily bolt on walters fencing racks.
Was designed to utilise 500m rolls and a plain wire below ringlock, level with bottom middle and top of ringlock which ended up being cheaper and quicker than 200m rolls with 1 plain wire due to cost saving between the 500m and 200m rolls.
Was designed for a sighter wire to be ran on the first pass, the trailer to hit in every post, run all the plain wires and ringlock on the second pass and be strained, than somebody walking/driving along clipping or tying the ringlock on. Effectively have a fence completed by driving up a graded line twice/three times.
Used to put a winch in the trailer pull and strain the ringlock up at the end assemblies.
Used as a fencing trailer briefly, worked extremely well however ended up using it to cart around yard building gear predominately.
Capable of comfortably doing roughly 1.3km of ringlock fencing each day or 2.2km of plain wire fencing with strainers already installed depending on operator.
With ringlock rates at $5.50m for ringlock and $3.50 for plain in current area it’s a good opportunity for a a farmer to save money or somebody looking to make an extra income.
Selling due to change of circumstances.
$16500 GST inclusive.
Located Horsham VIC but could meet somewhere closer to purchaser if it made it easier etc
4.2m x 2.4m flat top trailer
Built in 2020
Ladder rack
Ringlock arms to suit both 500m and 200m rolls
50mm RHS under trailer on 45 degree to straighten bent star posts if needed. Have never needed to do it.
Chequer plate on pull to sit wire spinners on or either put them on back of Ute
Arm to suit spring balancer and Marchant/Christie post driver
Rear Hayes trailer pull
3.5t simplicity suspension. Was designed with a load sharing suspension to be able to let tyres down and use in wet weather with snow chains. Haven’t actually tried it though.
Fits maxi posts and normal posts
Note doesn’t come with post racks. Can easily bolt on walters fencing racks.
Was designed to utilise 500m rolls and a plain wire below ringlock, level with bottom middle and top of ringlock which ended up being cheaper and quicker than 200m rolls with 1 plain wire due to cost saving between the 500m and 200m rolls.
Was designed for a sighter wire to be ran on the first pass, the trailer to hit in every post, run all the plain wires and ringlock on the second pass and be strained, than somebody walking/driving along clipping or tying the ringlock on. Effectively have a fence completed by driving up a graded line twice/three times.
Used to put a winch in the trailer pull and strain the ringlock up at the end assemblies.
Used as a fencing trailer briefly, worked extremely well however ended up using it to cart around yard building gear predominately.
Capable of comfortably doing roughly 1.3km of ringlock fencing each day or 2.2km of plain wire fencing with strainers already installed depending on operator.
With ringlock rates at $5.50m for ringlock and $3.50 for plain in current area it’s a good opportunity for a a farmer to save money or somebody looking to make an extra income.
Selling due to change of circumstances.
$16500 GST inclusive.
Located Horsham VIC but could meet somewhere closer to purchaser if it made it easier etc
Your Review
You don't have any recently viewed items
Any items you have viewed recently will be displayed here
•••• ••• 2521