40 views
LS3 intake manifold with all the good bits...
$650
Complete stock intake from a 90,000km engine L98.
Fuel rail
injectors
throttle body
sensors
I've bought a water-to-air intercooler type manifold, so have no need for this now.
It's in excellent condition.
Fuel rail
injectors
throttle body
sensors
I've bought a water-to-air intercooler type manifold, so have no need for this now.
It's in excellent condition.
- Date Listed:19/04/2024
- Last Edited:19/04/2024
- Condition:Used
- Warranty:No
- Transmission:Other
Similar Ads
- Toyota 4AGE 20v Silvertop factory ITB Ram tubeSet of 4 ITB's for intake manifold on 4AGE 20v Silvertop. Postage $15 or free pick up. Also have a piece of Aluminium 40cm x 19 cm x 6mm if you wish to make an adaptor plate $10.$60NegotiableOak Flats, NSW•140w
- 6 x 22mm BMW Swirl Flap Removal Blanking PlatesPurchased these a few years back and were never used as the were too small. They may be slightly salty from my tears over having to reassemble the intake manifold and order the right ones and do the job another time.$30Coniston, NSW•164w
- Ls1 t56 manual conversionSelling manual conversion. What I have T56 A good billet products short shifter Cross meber All lines Slave master ect 5 puck brass button clutch fly wheel ect Clutch pedel “There is no gear boot or floor plate. “ Cheap from eBay For extra can come with manual vy loom Suit. Vt vx vy vz. Ls1. Drift. Burnout car ect. Wollongong nsw$3,000Berkeley, NSW•9w
- 1jz jzx100 parts / CT15B turboSelling a couple things of my jzx100 chaser as I have gone to a high mount set up Ct15b and Manifold,first piece of downpipe, heat shield and turbo lines - $350 all in good working order (or $400 including cat) 1jz J pipe - $100 also in good working order May also have the old side mount and pipes if needed, real crusty but was working fine prior to removal - $50 Also selling a white trd chaser wing - $450 see other listing$500Barrack Heights, NSW•69w
- Turbo 400 Transbrake barra chev ls rb 2j 355 383 408 427 454 408Transbrake t400 barra ls rb 2j can build to suit your engine using only the best parts I don’t build cheap gearboxes I only use good quality parts I build Powerglides as well to suit nearly every engine combination 2j rb barra ls lsa etc if your after a cheap rubbish gearbox im not the one to ask try someone else please no dreamers$77,777,777NegotiableWollongong, NSW•16w
- Turbo setup for skyline rb26 rb25 rb30 r31 r32 r33 vl commodoreGarrett gt35 turbo high flow, etm exhaust manifold dump pipe and turbosmart waistgate 500 to 800 hp setup suit rb25 or rb26 or rb30/26 or rb30/25 everything ready to go turbo only done 2000kms since rebuild selling as I have gone bigger all off the car but can put back on if anyone want to test have got a gtx3582r gen 2 if anyone would like that with setup instead of of the gt35 cost $3800 only done 1 dyno run on 25psi$1,900Dapto, NSW•19w
- Holden Commodore VZ V6 Air Intake Joiner Rubber Boot - Duct TubeHolden Commodore VZ V6 Air Intake Rubber Joiner-Boot-Tube. No tears or holes. 3 available. $20 Each. Postage Available.$20NegotiableWollongong, NSW•17w
- Vw transporter t5 diesel 2.5 inlet manifoldVw t5 transporter inlet manifold diesel turbo$200NegotiableWollongong, NSW•30w
- Mini inlet manifold complete r50r51 miniInlet manifold complete with injectors and throttle body r50 r51 mini$250NegotiableWollongong, NSW•36w
- Mitsubishi Pajero NM 3.5L V6 stainless manifold replacement LHS HiTechA new stainless steel manifold replacement for a Mitsubishi Pajero NM 3.5L passengers side HiTech headers, for a cracked manifold$150Cordeaux Heights, NSW•27w
You don't have any recently viewed items
Any items you have viewed recently will be displayed here
•••• ••• 1157