43 views
K20 K24 Kswap K-tuned EP3 idler pulley and bracket kit
$200
selling my K-tuned EP3 adjustable billet pulley and bracket kit.
Suits K20 and K24 engines.
Comes with:
K-tuned billet pulley and bracket
K-tuned 7PK1283 belt
OEM Honda kseries auto tensioner
Bolts
The belt that comes with this kit is designed for a k20 crank pulley, I used this kit on with a K24 crank pulley and with the bracket on the lowest setting and the tension was out of the acceptable range. If your worried about this you can use a k20 crank pulley or use some string to measure the length and buy a larger belt.
The bearing in the K-tuned pulley is on its way out (K-tuned notoriously use cheap chinese bearings in their products) this can be replaced with a OEM Honda bearing for $20, its the same part number as the pulley bearing on the auto tensioner.
Can post Australia wide @ buyer's expense or pick-up from Terrigal, 2260, NSW
Suits K20 and K24 engines.
Comes with:
K-tuned billet pulley and bracket
K-tuned 7PK1283 belt
OEM Honda kseries auto tensioner
Bolts
The belt that comes with this kit is designed for a k20 crank pulley, I used this kit on with a K24 crank pulley and with the bracket on the lowest setting and the tension was out of the acceptable range. If your worried about this you can use a k20 crank pulley or use some string to measure the length and buy a larger belt.
The bearing in the K-tuned pulley is on its way out (K-tuned notoriously use cheap chinese bearings in their products) this can be replaced with a OEM Honda bearing for $20, its the same part number as the pulley bearing on the auto tensioner.
Can post Australia wide @ buyer's expense or pick-up from Terrigal, 2260, NSW
- Date Listed:05/04/2024
- Last Edited:05/04/2024
- Condition:Used
- Body Type:Coupe (2 door)
- Warranty:No
- Transmission:Manual
- Model:Integra
- Make:Honda
- UrgentBuilt Barra Atomic Performance 998 - GTA long motorselling my fully sick and fully built barra Atomic Performance 998-GTA spec long motor mods: ACL Competition rod bearings ACL 360degree thrust bearings Atomic FatRods Atomic Stage 4 camshafts Atomic Stage 2 prep crankshaft (mangafluxed and micropolished) Multi-angle valve ported head @ 30. 45. 65 degrees rotating assembly Dynamically balanced engine block bored .5mm over standard engine block torque plated and honed Atomic harmonic balancer - Race series Atomic 12-pt balancer bolt w/ washer At$15,000NegotiableTerrigal, NSW•1d
- HONDA EG EK DC2 Front Suspension Sale HARDRACESelling front suspension setup to suit HONDA EG EK DC2 with HARDRACE bushings. I cleaned up all the arms, painted them in VHT epoxy single stage black paint. The bushings were on my car for < than 1 month, they are in near new condition, still got plenty of life in them. HARDRACE hardend rubber front compliance bush - $75 Front shock forks suit EG/DC2 - $75 Front complete lower arms with HARDRACE hardened rubber bush - $300 or the whole lot for $400 Can post australia wide @ buyer's exp$400NegotiableTerrigal, NSW•2w
- Hardrace RTA hardened rubber bush Honda EG EK DC2selling my Hardrace rear trailing arm hardened rubber bushes to suit Honda civic Integra EG EK DC2 Bushes are brand new not 1 single km on them, they have been installed into my trailing arms and I've removed them going to a poly bush setup. I can install these with my press into your car or trailing arms if you bring them to me for an extra $50. Can post Australia wide @ buyer's expense or pick-up from Terrigal, NSW, 2260$80Terrigal, NSW•3w
You don't have any recently viewed items
Any items you have viewed recently will be displayed here