642 views
Everlast powerpro 256si AC/DC TIG/PLAZMA CUT/STICK welder 3phase 415V
$1,550 Negotiable
SHIPPING OFFERED
selling my 3phase Everlast powerpro 256si AC/DC tig/plasma cutter/stick welding machine
technical data:
IGBT inverter
3phase 415V power with 32amp 4pin plug
AC/DC tig output
high frequency tig start
adjustable pulse
blow back (piston type) plasma cutter arc start
pilotArc
20-250hz AC frequency
10-90% AC balance (cleaning)
85V OCV
TIG output Amps/Volts @ rated duty cycle:
250A/20V @ 60% duty cycle
200A/18V @ 100% duty cycle
Stick output Amps/Volts @ rated duty cycle:
200A/28V @ 35% duty cycle
160A/26.4V @ 60% duty cycle
130A/25.2V @ 100% duty cycle
Plasma output Amps/Volts @ rated duty cycle:
60A/104V @ 35% duty cycle
50A/100V @ 60% duty cycle
40A/96V @ 100% duty cycle
TIG AC Amp/Volt range: 20A-250A; 10.8V - 20V
TIG DC Amp/Volt range: 5A-250A; 10.2V - 20V
Stick Amp/Volt range: 5A-200A; 20.2V - 28V
Plasma Amp/Volt range: 20A-60A; 88V - 104V
0-25 seconds down slope time
0-10 seconds up slope time
0-10 seconds gas pre-flow time
0-25 seconds gas post-flow time
0.5-250Hz Tig pulse frequency
10-90% Tig pulse time on
5-95% Tig pulse Amp range
10-100% stick arc force control
PT/iPT 60 torch type
7.5bar recomended cutting air pressure
30kg weight
56cm x 23cm x 43cm dimensions
this machine is in near new conditon i've used DC tig on it for less than 50hrs
runs on 3phase 415V power supply and its fitted with 32Amp 4 pin plug
comes with tig torch, foot pedal, argon regulator, stick torch and plasma torch
comes with custom made 3phase lead, 15M long with 32amp 4 pin male and female sockets on both ends
for any DIY/Garage guys who are interested in this machine and are not sure if you can get 3phase power but just open up your meter box and pull the switch board back and if you see 4 wires (3 red ones and 1 white one) behind the board a level 1 sparky can come and install 3 phase into your garage so long as there is room there for a 3 pole 415V circut breaker on the board itself. The average market price for a 4pin 32amp socket adjusted for today's inflation is around $80, plus, sparky call out fee, plus, conduit, plus, 2ish hours labour, It will probably cost around $350-450 to get the socket installed.
can post australia wide @ buyer's expense however this item is large, heavy and bulky so it wont be cheap
pick up at Terrigal, 2260, NSW
technical data:
IGBT inverter
3phase 415V power with 32amp 4pin plug
AC/DC tig output
high frequency tig start
adjustable pulse
blow back (piston type) plasma cutter arc start
pilotArc
20-250hz AC frequency
10-90% AC balance (cleaning)
85V OCV
TIG output Amps/Volts @ rated duty cycle:
250A/20V @ 60% duty cycle
200A/18V @ 100% duty cycle
Stick output Amps/Volts @ rated duty cycle:
200A/28V @ 35% duty cycle
160A/26.4V @ 60% duty cycle
130A/25.2V @ 100% duty cycle
Plasma output Amps/Volts @ rated duty cycle:
60A/104V @ 35% duty cycle
50A/100V @ 60% duty cycle
40A/96V @ 100% duty cycle
TIG AC Amp/Volt range: 20A-250A; 10.8V - 20V
TIG DC Amp/Volt range: 5A-250A; 10.2V - 20V
Stick Amp/Volt range: 5A-200A; 20.2V - 28V
Plasma Amp/Volt range: 20A-60A; 88V - 104V
0-25 seconds down slope time
0-10 seconds up slope time
0-10 seconds gas pre-flow time
0-25 seconds gas post-flow time
0.5-250Hz Tig pulse frequency
10-90% Tig pulse time on
5-95% Tig pulse Amp range
10-100% stick arc force control
PT/iPT 60 torch type
7.5bar recomended cutting air pressure
30kg weight
56cm x 23cm x 43cm dimensions
this machine is in near new conditon i've used DC tig on it for less than 50hrs
runs on 3phase 415V power supply and its fitted with 32Amp 4 pin plug
comes with tig torch, foot pedal, argon regulator, stick torch and plasma torch
comes with custom made 3phase lead, 15M long with 32amp 4 pin male and female sockets on both ends
for any DIY/Garage guys who are interested in this machine and are not sure if you can get 3phase power but just open up your meter box and pull the switch board back and if you see 4 wires (3 red ones and 1 white one) behind the board a level 1 sparky can come and install 3 phase into your garage so long as there is room there for a 3 pole 415V circut breaker on the board itself. The average market price for a 4pin 32amp socket adjusted for today's inflation is around $80, plus, sparky call out fee, plus, conduit, plus, 2ish hours labour, It will probably cost around $350-450 to get the socket installed.
can post australia wide @ buyer's expense however this item is large, heavy and bulky so it wont be cheap
pick up at Terrigal, 2260, NSW
- Date Listed:11/03/2024
- Last Edited:08/04/2024
- Brand:Other
- Condition:Used
- Shipping:Shipping & Pickup
- HONDA EG EK DC2 Front Suspension Sale HARDRACESelling front suspension setup to suit HONDA EG EK DC2 with HARDRACE bushings. I cleaned up all the arms, painted them in VHT epoxy single stage black paint. The bushings were on my car for < than 1 month, they are in near new condition, still got plenty of life in them. HARDRACE hardend rubber front compliance bush - $75 Front shock forks suit EG/DC2 - $75 Front complete lower arms with HARDRACE hardened rubber bush - $300 or the whole lot for $400 Can post australia wide @ buyer's exp$400NegotiableTerrigal, NSW•1w
- Hardrace RTA hardened rubber bush Honda EG EK DC2selling my Hardrace rear trailing arm hardened rubber bushes to suit Honda civic Integra EG EK DC2 Bushes are brand new not 1 single km on them, they have been installed into my trailing arms and I've removed them going to a poly bush setup. I can install these with my press into your car or trailing arms if you bring them to me for an extra $50. Can post Australia wide @ buyer's expense or pick-up from Terrigal, NSW, 2260$80Terrigal, NSW•2w
- Honda RDX injectors 410cc k20 k24 kswapSelling my set of GENUINE Honda/Acura RDX 410cc injectors No connectors included, they can be bought online cheap. They were on my car for < 1 month. Not sure if they are E85 friendly, probably not. These can be used on k-series and b-series as well if you buy an adaptor. Can post Australia wide @ buyer's expense or pick-up Terrigal NSW, 2260$250NegotiableTerrigal, NSW•2w
You don't have any recently viewed items
Any items you have viewed recently will be displayed here