117 views
TOA VM2240 240W Management Amplifier
$1,200
TOA VM2240 Multifunctional amplifier.
Can be mounted in an EIA-Standard equipment rack (3-unit size).
4 audio inputs including the background music input, and the speaker output section with an internal attenuator and 5-zone selector.
Allows general-purpose broadcast and also Emergency Broadcast based on the EN60849 Standard which gives pre-recorded voice instructions(*1) in the emergency situation.
Broadcast can be made from an optional RM-200M Remote Microphone as well as from the amplifier, and can be remotely controlled from external equipment.
Power Requirement AC mains, 50/60 Hz DC: 24 V
Output 120 W (VM-2120) / 240 W (VM-2240)
Frequency Response 50 – 16,000 Hz
Distortion Less than 1%
Signal-to-Noise Ratio More than 60 dB
Tone Control Bass: 100 Hz ±10 dB, Treble: 10 kHz ±10 dB (Inputs 1 – 3 and BGM individually adjustable.)
Remote Mic/Extension Amp Connection Two RJ45 female connectors Maximum distance: 800 m
Audio Input
Inputs 1 ~ 3 -60 dB*1 [MIC]/-10 dB*1 [LINE] (switchable), 600 Ω, electronically balanced*2, combined XLR type connector (female)/ 1/4″ phone jack (Only Input 1 is additionally (female)/ 1/4″ phone jack (Only Input 1 is additionally equipped with DIN connector*3.)
Telephone Paging Input Push-in terminal block
-10 dB*1, 10 k Ω, electronically-balanced*2
Control : No-voltage make contact input
BGM 1 – 2 -20 dB*1, 10 k Ω, RCA pin jack, monaural
Power Amplifier Input 0 dB*1, 10 k Ω, RCA pin jack
External Speaker Line Input 100 V line, for All-Zone Broadcast
Audio Output
Speaker Output 83 Ω (100 V line, volume control in maximum position), Removable terminal block with screw terminals.
Speaker Zone Control 5-zone selector with attenuator
Direct Speaker Line Output Direct output from the power amplifier output transformer
Line Output 0 dB*1, 10 k Ω, RCA pin jack
Recording Output 0 dB*1, 10 k Ω, RCA pin jack
Preamplifier Output 0 dB*1, 10 k Ω, RCA pin jack
Control Inputs 1 – 3 For controlling Inputs 1 – 3, Push-in terminal block
No-voltage make contact.
Control Input and Output Control Input and Output
Input : No-voltage make contact input
Output : Open collector output
(1) External control input
Activation of messages for an optional Voice Announcement Board*4
Activation of power
Activation and stop of Emergency Broadcast
Unit’s broadcast cutoff (when activated by an external emergency equipment)
(2) Status output
Irregularity of communications with the Remote Microphone and an expansion amplifier
AC power condition
DC power condition
Irregularity of the sound source of the Voice Announcement board
Stop of the unit’s broadcast
External Attenuator Control Output Removable terminal block with screw terminals, relay, no-voltage make contact output, transfer type
Surveillance Input and Output*5 25-pin female D-sub connector
Input : No-voltage make contact input
Output : Open collector output
Power Output 24 V DC
Chime Tone Built-in chime:
2-tone chime/2-tone chime(fast repeat)
4-tone chime (Up)/Single-tone chime/4-tone chime (Up & Down)/Gong/off
Finish Panel: ABS resin
Case: Steel plate painted
Dimensions 419 (W) × 143.3 (H) × 356.2 (D) mm
Comes with all Cable, Connectors and Manual.
Very Good condition with a couple of small marks to top panel.
This unit is tested but Sold as in 'as is' condition.
Returns considered on a case by case basis.
All Items located in Sydney for delivery or pickup.
These are Vintage units...please do not expect it to look like or necessarily perform like it just left the showroom floor.
Delivery East Coast is approximately 6 Business Days elsewhere is longer.
I accept Bank Deposit/Transfer, Paypal or Cash on Pickup. East Coast Postage - $55.00, WA/NT add $30.00, Nth QLD add $30 and Tasmania/SA add $20.00 to quoted postage.
Can be mounted in an EIA-Standard equipment rack (3-unit size).
4 audio inputs including the background music input, and the speaker output section with an internal attenuator and 5-zone selector.
Allows general-purpose broadcast and also Emergency Broadcast based on the EN60849 Standard which gives pre-recorded voice instructions(*1) in the emergency situation.
Broadcast can be made from an optional RM-200M Remote Microphone as well as from the amplifier, and can be remotely controlled from external equipment.
Power Requirement AC mains, 50/60 Hz DC: 24 V
Output 120 W (VM-2120) / 240 W (VM-2240)
Frequency Response 50 – 16,000 Hz
Distortion Less than 1%
Signal-to-Noise Ratio More than 60 dB
Tone Control Bass: 100 Hz ±10 dB, Treble: 10 kHz ±10 dB (Inputs 1 – 3 and BGM individually adjustable.)
Remote Mic/Extension Amp Connection Two RJ45 female connectors Maximum distance: 800 m
Audio Input
Inputs 1 ~ 3 -60 dB*1 [MIC]/-10 dB*1 [LINE] (switchable), 600 Ω, electronically balanced*2, combined XLR type connector (female)/ 1/4″ phone jack (Only Input 1 is additionally (female)/ 1/4″ phone jack (Only Input 1 is additionally equipped with DIN connector*3.)
Telephone Paging Input Push-in terminal block
-10 dB*1, 10 k Ω, electronically-balanced*2
Control : No-voltage make contact input
BGM 1 – 2 -20 dB*1, 10 k Ω, RCA pin jack, monaural
Power Amplifier Input 0 dB*1, 10 k Ω, RCA pin jack
External Speaker Line Input 100 V line, for All-Zone Broadcast
Audio Output
Speaker Output 83 Ω (100 V line, volume control in maximum position), Removable terminal block with screw terminals.
Speaker Zone Control 5-zone selector with attenuator
Direct Speaker Line Output Direct output from the power amplifier output transformer
Line Output 0 dB*1, 10 k Ω, RCA pin jack
Recording Output 0 dB*1, 10 k Ω, RCA pin jack
Preamplifier Output 0 dB*1, 10 k Ω, RCA pin jack
Control Inputs 1 – 3 For controlling Inputs 1 – 3, Push-in terminal block
No-voltage make contact.
Control Input and Output Control Input and Output
Input : No-voltage make contact input
Output : Open collector output
(1) External control input
Activation of messages for an optional Voice Announcement Board*4
Activation of power
Activation and stop of Emergency Broadcast
Unit’s broadcast cutoff (when activated by an external emergency equipment)
(2) Status output
Irregularity of communications with the Remote Microphone and an expansion amplifier
AC power condition
DC power condition
Irregularity of the sound source of the Voice Announcement board
Stop of the unit’s broadcast
External Attenuator Control Output Removable terminal block with screw terminals, relay, no-voltage make contact output, transfer type
Surveillance Input and Output*5 25-pin female D-sub connector
Input : No-voltage make contact input
Output : Open collector output
Power Output 24 V DC
Chime Tone Built-in chime:
2-tone chime/2-tone chime(fast repeat)
4-tone chime (Up)/Single-tone chime/4-tone chime (Up & Down)/Gong/off
Finish Panel: ABS resin
Case: Steel plate painted
Dimensions 419 (W) × 143.3 (H) × 356.2 (D) mm
Comes with all Cable, Connectors and Manual.
Very Good condition with a couple of small marks to top panel.
This unit is tested but Sold as in 'as is' condition.
Returns considered on a case by case basis.
All Items located in Sydney for delivery or pickup.
These are Vintage units...please do not expect it to look like or necessarily perform like it just left the showroom floor.
Delivery East Coast is approximately 6 Business Days elsewhere is longer.
I accept Bank Deposit/Transfer, Paypal or Cash on Pickup. East Coast Postage - $55.00, WA/NT add $30.00, Nth QLD add $30 and Tasmania/SA add $20.00 to quoted postage.
- Date Listed:13/08/2022
- Last Edited:13/08/2022
- Condition:Used
Similar Ads
- TOA PA Microphone PM-660U 600 Ohm DesktopTOA PA Microphone PM-660U 600 Ohm Desktop Desktop PA System Microphone Note; one unit has the cable damaged at base, as seen in picture, both are working. Suits the TOA Amplifier also listed. Pickup from Hassall grove or can be posted at extra cost Please see other listed items.$55SHIPPING OFFEREDRooty Hill, NSW•52w
- Accuphase Stereo Integrated Amplifier E-305 (240V)Accuphase stereo integrated amplifier E-305, works without any problems. (240 V) It comes with the original box and original instruction manual. It Is in a very good condition considering its age. You're welcome to audition the device. Supply voltage is 100 - 120 - 220 - 240 VAC internally adjustable.$4,800SHIPPING OFFEREDNegotiableAsquith, NSW•27w
- PYLE PLMRA120 240-Watt 2-Channel Waterproof Marine/Car AmplifierBrand new This Pyle Hydra amp will power your speakers on the dock, in your boat, or by the pool--it's completely waterproof. This 2-channel, 240-watt marine amp takes both high- and low-level inputs, so it's compatible with a variety of head units and sources. Remote turn/on off makes controlling the amp a breeze, and gold-plated RCA inputs mean it won't be a weak link in your setup. Power your speakers on the dock, in your boat, or by the pool. View a connection diagram. Input Options$89Bella Vista, NSW•421w
- Biam Devio Conferencing Hub and Tabletop Microphone (DTM1)Biam Devio Conferencing Hub and Tabletop Microphone (DTM1) Model: CR-1T Brand New (unopened) Biamp Devio CR-1 Conference Room Dock System with DTM-1 Tabletop Beam Tracking Conferencing Microphone The Devio CR-1 creates a desktop-like experience away from the desk, allowing you to make an easy transition to the meeting room simply by detaching your laptop from your desk and connecting to Devio via USB 3.0 in the meeting room. Devio’s included beamforming DTM-1 microphone provides 360-degree c$2,800St Clair, NSW•12w
- Toa A-1724 Black PA System 033700228844Condition: Functional, with heavy wear Delivery options: Regular Postage: 4 – 10 days – $35.20 Express Postage: 2 – 6 days – $52.45 (Includes insurance & signature on delivery) Store Pickup: Free - available in store Product details: Item Number: 033700228844 Brand: Toa Model Number: A-1724 Colour: Black Accessories: This item does not include any accessories. Please note: The postage price listed for this item is for LOCAL DELIVERY ONLY. Please contact us for a courier quote prior to$135SHIPPING OFFEREDBlacktown, NSW•5w
- 50W Digital Power Hifi Amplifier With Stereo 2.1 newFeatures: A920-50W digital power amplifier: imported into the control chip system, first-class quality, good sound, increase the treble bass adjustment function, large power, high dynamic, powerful voice, full, wide field open, powerful bass, showed considerable thickness, the voice is very magnetic sound, smooth, full sound, high frequency performance, especially high frequency, brightness, suitable for long time to listen to, if there is a strong sense of three-dimensional, open wide sound f$95Sydney City, NSW•338w
- Used/Working STK430 III 10W - 2 channel audio amplifier JG1USED - EQUIPMENT PULL - legs are not shortened STK 430 III Stereo hybrid mono block amplifier ESTIMATED 10W RMS output per channel Typically using a Vcc of around 25V Datasheets for this hybrid chip seems difficult to find, still useful as a "drop in" replacement device $4 is our price TT2018$4Rooty Hill, NSW•296w
- Yamaha AS2000 Integrated AmplifierYamaha AS2000 Integrated Amplifier for sale in very good condition (no original remote)$1,650South Hurstville, NSW•33w
- STK 011 - 6.5W Single channel audio amplifier BRAND NEWWelcome to our time tunnel of electronics To see my other electronic spare parts, try searching on ELECTRONIC SPARE TIME TUNNEL STK 011 Single channel audio amplifier Typically using a Vcc of 25V Power Amplifier Minimum 6.5 Watts RMS audio output into 8 Ohms load NEW - NEVER BEEN USED Datasheets for these hybrid chips are easily obtainable online This audio amplifier hybrid chip is also available on our own site @ time-tunnel $8 is our price TT2019 We can ship$8Rooty Hill, NSW•247w
- Integra DTR 80.1 AmplifierUsed Integra DTR 80.1 amplifier for sale with Remote. Fully functional and only some surface on top of the unit. Great sounding amplifier for Surround sound and audio listening$350Miranda, NSW•16w
- Vintage Aiwa MX70/TX70/FX70/SX7 Mini System + D50 Tray Load TurntableVintage Aiwa MX70/TX70/FX70/SX7 Mini System + D50 Tray Load Turntable from the 1980s. Very cool outfit and rare. MX70 Amplifier TX70 AM/FM Tuner FX70 Stereo Cassette Deck SX7 2 way Speakers D50 Tray load 2 Speed Direct Drive Auto Turntable Everything is functioning well and in good cosmetic condition. I sell Retro Hifi professionally so all my equipment is cleaned, tested and operating correctly unless otherwise stated. Returns considered on a case by case basis. All Items located in Sydney$750SHIPPING OFFEREDWareemba, NSW•11h
- Vintage Wharfedale Diamond II Bookshelf SpeakersGreat pair of Wharfedale Diamond II Bookshelf Speakers from the 1980s. Specification: System type: Two-way. Enclosure type: Reflex. Impedance: 8 ohms. Amplifier requirements: 10-75 W Max power input: 100 W Frequency response: 50Hz to 20kHz. Crossover point: 5KHz. Sensitivity: 86dB. Dimensions (H x W x D): 240 x 186 x 205 mm. Very good with a couple of very light marks and pinholes for cloth to a couple of corners. I sell Retro Hifi professionally so all my equipment is cleaned, tested and ope$150SHIPPING OFFEREDWareemba, NSW•2d
- Vintage Bose 301 Series 1 SpeakersPair of classic Bose 301 Series 1 Bookshelf Speakers from the 1970s. Type: 2 way, 2 driver loudspeaker system Recommended Amplifier: 10 to 60W Impedance: 8Ω Bass: 1 x 8" cone - Original replaced with top quality American Speaker Tweeter: 1 x 3" cone Enclosure: ducted port Dimensions: 17 x 19.5 x 9.25 inches Very good with a couple of very light marks. Original foam grilles which are fragile due to age. I sell Retro Hifi professionally so all my equipment is cleaned, tested and operatin$350SHIPPING OFFEREDWareemba, NSW•2d
You don't have any recently viewed items
Any items you have viewed recently will be displayed here