17 Results: New & Used in Cars & Vehicles in Ashtonfield 2323, NSW

Trailer 6x4, manufactured by Trailers 2000. Galvanised trailer with ladder racks, jockey wheel and rubber floor mat. Size 6x4, 160kg tare, max 750 kg. Registered to January 2025.

Davies Craig Transmission Oil Cooler Part no 678 Suits 4.0 litre and over, brand new Latest 21 plate and fin Hydra design 33% more efficient than a comparable tube and fin design Cost $199 at Auto One Selling for $119

Bit of surface rust that will sand out. Comes with one key Pick up Ashtonfield

A pair of rear Koni adjustable shocks out of my VL Walky, which I sold recently with original Bilsteins fitted. Come with mounting rubbers and if I can find it the hand adjuster. Should also fit VH, VK. One is nice and firm, the other a bit weak and may need reconditioning, so selling cheap. Will include shipping to Metro and some regional areas. Advise PC and suburb to confirm free shipping.

I removed this from a 2000 model WRX. According to Whiteline it is a BSR20XZ 22mm adjustable rear sway bar to suit a WRX/STI 94-07 and Forester SF $356 Also has the KLC26 sway bar link assembly $231 Currently selling as a kit for $500 total. This sway bar is in as new condition. I live ten minutes past the Newcastle end of the Sydney/Newcastle freeway.

Brand new suits black dash Matt suits VX

VESPA 60,S ? NEW OLD STOCK CONROD AND BOTTOM END BEARING AND GENUINE GEARBOX CRUCIFIX , THE CONROD BEARING STILL HAS THE ORIGINAL GREASE AND FACTORY RUBBER RETAINING RING. GENUINE NEW GEARBOX CRUCIFIX. UNSURE OF WHAT MODEL/S THEY SUIT AS IT WAS PART OF MY LATE FATHERS [VESPA MECHANIC ] PARTS. SORRY,HAVE NO OTHER PARTS, THIS IS ALL THAT IS LEFT. SELLING CHEAP ,WANT IT GONE TO SOMEONE WHO CAN USE IT. POSTAGE IF NEEDED WILL BE $12.00 IN AN AUS POST PARCEL SATCHEL TO ANYWHERE IN AUSTRALIA. THANKS F

Brand new Goss MAP Sensor to suit all engines in EA, EB, ED and EF models. Purchased but not used due to selling car. Free postage in OZ

Subaru Outback Window switches. Came from a 2012 but suits 2009 - 2013 outbacks. Drivers door panel $50 All other doors $30. Any questions please ask.

A pair of front reconditioned and modified Bilstein shocks that were fitted to my VL Walky. Should suit any VH-VL with coil overs. They were reconditioned and modified by Paul at Bilstein (Heasmans) to suit 620/700 lb springs for track work but only had them in for a short time before I sold the car so only used for around 2000 K's road and track. For the $200 will include either 620 lb with ID of 61.0 mm and free length of 200.0 mm springs OR 700 lb with ID of 66.0mm and free length of 184

R33 tail shaft complete except for front input shaft/yoke (used on another car to fit an R33 gearbox). Unis and centre bearing seem to be in good condition. Has bolts to assemble as one unit. Ideal for rear section replacement due to worn or damaged universal or CB, or if fitting another gearbox that needs a different input shaft/yoke.

RB25 OEM Turbo that has been high flowed. Looks to be in reasonable condition but needs new bearings due to excessive end play. Turbine wheel looks OK but is non-ferrous. Compressor wheel has chip out of one blade. In let dia 55.0mm and outlet 58.0mm. Was going to recondition and use but instead went with different unit. Will include shipping to any metro and some regional addresses.

A set of solid lifters to suit the Walky 304 engine in good cinditionto suit solid cam with no pitting on base. Took them out after 10,000Km and replaced with hydtraulic cam and lifters. Should fit all 304 engines.

For sale out of an EA Falcon: radius rods (caster bars) $20 pr top A arms $20 pr springs and shocks $30 pr or $50 the lot. Probably also suits EB-ED. Some components only have surface rust. All are in good condirion, no damage.

For sale a pair of brand new tie rods to suit a Series 1 EA Falcon. They are the 14 mm dia x 1.75 mm thread to suit early EA's.

Brand new, oil filled engine mount to suit a W202 C240 or C200 MB. Still in its plastic wrapper. Bought two to fit to my 1997 C240 but only needed one.

Spare clutch (driven) plate off my VL Walky now sold. Springs are tight and facings still have some wear left. Fits T5G gearbox input shaft so should also fit VL HDT SS Group A and any other car witg a T5G gearbox..