254 Results: New & Used in Engine, Engine Parts & Transmission in Lakelands 2282, NSW

Turbo diesel AWD gearbox with aprox 180.000 kilometres Gearbox with converter transfer case and front tailshaft No longer needed $1800

Been stored out of weather many years was for project not used

Good condition manual gearbox from a 1993 non turbo 2.1 with only 180k on the clock I have many other parts including complete 2.1 engine

For sale is new in box quality brand GMB Water Pump to suit 1AZ n 2AZ engines Inc gasket. Was not required and vehicle no longer in the family. Item location Newcastle Lake Macquarie NSW 2284 Pick up n cash only Cheers

I have for sale a Protex brand Water Pump to suit Triton and some other models that share same motor. New never fitted kit which was incorrectly supplied. Includes gaskets and O Ring. Please do your own research regarding correct application as no returns. Protex part number is WP3144. Pick up and cash only. Location is Newcastle, Lake Macquarie 2284 Cheers

I have a new never fitted surplus to requirements Concentric Slave Cylinder for various Toyota models. Please see pics for application. These retail close to $300.00 Item location is Newcastle , Lake Macquarie NSW 2284 Cash only . Cheers

4ze1 parts all parts are new cam seal valve steam seals tappet cover bolt seals/washers and rubber seal for back of tappet cover /head 2 manifold gaskets 2 bottom manifold gaskets and a bunch of orings and other gaskets new fuel pump 94 to 98 38mm round pick up charlestown nsw 2290

94 to 98 2.6 4ze1 rodeo parts ( will swap for 90 to 93 parts front fenders no rust a grill a right mirror a blown up 4ze1 engine ) red top injectors cleaned and tested and in good condition with new seals will need to install them injector rail with spacers ( fuel pressure regulator sold ) injector and intake wire harness throttle body with half of intake and tps check out my other listings listed elswhere pick up charlestown nsw 2290

CVS. 1187L drive shaft. Suit******2015 4x4 Hilux. These are the longer shaft to suit 2” plus lift. I only had these in for around 2 months. Like new. $150 for the pair

1850-14 Holley Performance Carb Sat on an engine, displayed only. Never used, tarnished but new on the inside.

💥💥LOCATED NEWCASTLE NSW💥💥 💥💥💥💥PICK UP ONLY💥💥💥💥 Dual AVCS 2018 VA WRX STI EJ257 Removed at 53,436KM Great compression with 140-145 across all cylinders Complete engine minus a turbo, Turbo sold separately

The was fully operational before being removed from a 1986 Corvette.

From a 86, work perfectly. I have a video of them operating.

Nissan GU power steering pump.

4ze1 Distributor 4ze1 Distributor was out of a 94 rodeo I do have a cap and rotor button parts are in good used condition will add a pic of the cap and rotor button in the next few days check out my other listing and I will be listing a hole 91 duel cab rodeo that needs work or could used for parts soon located Charlestown nsw 2290

Radiator Copper/Natrad, Good condition/see pics Suits 1965 Holden Bedford 307 Chevrolet Manual Radiator Purchased approximately 1999 Will suit old school small & big block V8’s. Can post at buyers expense

6 pack only Suits falcon 6 cylinder BA - BF (not gas) Also suits other vehicles as stated in photo

- 3" piping - Bell mouth design - 3x O2 sensor ports for easy installation - 'Cat style' resonator - Corrosion resistant, polished stainless steel piping and components. Coated, corrosion resistant steel flanges - TIG welded - Mandrel Bent - Gaskets and bolts included This down pipe will significantly increase the flow and performance of your FA20 WRX.

Ported LS3 Intake Manifold (For V8 Commodore). All unnecessary obstructions have been removed (supports, protrusions, etc) and rod mod installed. Goes great but I'm getting rid of it as it makes the engine a fair bit more noisy down low. Car definitely feels like it pulls harder with the ported intake. If you don't know what the rod mod is, google it. Some say it's good for an extra 10-15hp. Support holes plugged with custom cut aluminum and sealed with rtv silicone. Bolts holding the rods ar

With 350 chev 4 bolt main Rebuildable condition ok

Tial 38mm external wastegates - two of, never used, also there's a pair of fabricated turbo exhaust manifolds to suit a LS1 that if you want I'll include them as well, I didn't make them I don't know what vehicle they suit, they're unused as well.

Bought for a conversion which it wasn’t suited for ( to big for the conversion) Brand new Never installed Never fitted Havnt even opened the haltech plug bag

3/4 full Pick up Elermore vale only

Mini breather 12mm neck Clamp on Bought brand new never used Pick up Elermore vale only