33 Results: excavator 322 in Australia

Price includes GST. New Jea Wen JW450 Excavator Hydraulic Hammer Rock Breaker to suit: 1-3 ton machine. Great for loosening and breaking up rock, rocky ground, concrete, tarmac, paved areas, demolition etc. Comes with a 43.6mm Point Moil, Hoses, Manual, Toolbox with various Spanners etc. and a Nitrogen Gas Bottle & Pressure Gauge Kit for regassing the breaker. The Hitch Headstock currently has 30mm Pins fitted into collar bosses that fit into 45mm diameter Pin holes, so pins up to 45mm diame

Price includes GST. New Jea Wen JW530 Excavator Hydraulic Hammer Rock Breaker to suit: 2-5 ton machine. Great for loosening and breaking up rock, rocky ground, concrete, tarmac, paved areas, demolition etc. Comes with a 52mm Point Moil, Hoses, Manual, Toolbox with various Spanners etc. and a Nitrogen Gas Bottle & Pressure Gauge Kit for regassing the breaker. Required Oil Flow: 25-45 L/min. Current Headstock Setup: * The Hitch Headstock currently has 40mm Pins fitted into collar bosses that

Price includes GST. New Ironfist I-10 Excavator Hydraulic Silenced Hammer Rock Breaker to suit: 9-20 ton machine. Great for loosening and breaking up rock, rocky ground, concrete, tarmac, paved areas, demolition etc. The Breaker is New & Unused. Comes with 2x 97mm Point Moils and a Nitrogen refilling Bottle. Required Oil Flow: 80-110 L/min. Required Pressure: 150-170 bar (2175 to 2465 psi). Breaker Dimensions (without moil, as seen in pics): 1740mm(L) x 480mm(W) x 550mm(H), Weight: 942kgs.

The price includes GST. New 200mm Excavator Digging & Trenching GP Bucket suit 1-3 Ton machine. This bucket has come from surplus stock from Atlas Heavy Engineering (AHE): https://ahe1.com.au. It is New & Unused but has some paint scuffs & chips from warehouse storage & handling. Some buckets have the manufacture's nameplate affixed, some do not, but all are the same. We have this bucket in 2 different Headstock Configurations: *** 1st Headstock configuration: 30mm Pin Diameter, 124mm Pi

The price includes GST. Used Caterpillar 400mm Excavator Digging & Trenching GP Bucket suit 1-3 Ton machine. Condition is used and there is some light rust and pitting from water sitting in it. But this is a well engineered, good solid bucket with plenty of life left. It has bolt-on removable Side Cutters, and has Tapered sides so mud slides out easy and minimises ground resistance. There is also extra wear strips welded underneath for durability (see pic# 9). This is a quality bucket made

The price includes GST. New 800mm AHE Excavator Mud Batter Bucket Bucket suit 1-3 Ton machine. This bucket has come from surplus stock from Atlas Heavy Engineering (AHE): https://ahe1.com.au. It is New & Unused but has some paint scuffs & chips from warehouse storage & handling. Some buckets have the manufacture's nameplate affixed, some do not, but all are the same. We have this bucket in 2 different Headstock Configurations: *** 1st Headstock configuration: 30mm Pin Diameter, 124mm Pin

The price includes GST. New Excavator Hydraulic Thumb Grapple Grab Bucket suit 1-3 Ton machine. The bucket moves as a normal bucket attached to your hitch or directly to your dipper arm. The Thumb moves Hydraulically. Designed for Rock & Log work, but can also be used for demolition and general material handling, picking things up, moving them around and other careful placement tasks. Required Oil Flow: 25-30 L/min. Working Pressure: 100-110 bar. Headstock Dimensions: * The Pin Diameter is

The price includes GST. New Miller Backhoe Excavator Mechanical Quick Hitch Coupler to suit Caterpillar Backhoe 416D, 416E, 420D, 428 C3, 428 C3D, 432 C3, 438 C3 and possibly other 3-9 Ton Excavators. Want a quick hitch but don't have any spare auxiliary hydraulic lines for a hydraulic hitch? This hitch is identical to a hydraulic hitch setup except you lever the pin clasp open and closed with a rod that compresses the spring. There is no need to pull either of the pins out of your buckets e

The price includes GST. Used Miller TwinLock PowerLatch Excavator Hydraulic Coupler Quick Hitch to suit 5-11 Ton machines. Designed for Kubota PL-2 but will fit other machines (see below list of machines we have found so far). 60mm Pin Diameter, 322mm Center to Center, 216mm Between the Ear Plates (203mm Between the Ear Bosses which could be shaved back up to 216mm if you need more inside width for your dipper arm to fit). Lifting Eye rated: Safe Working Load (SWL) 5,000kg. Hitch dimensions

The price includes GST. Used Excavator Hydraulic Quick Hitch Coupling to suit 15-32 Ton machines. The front hooks that grab the bucket's front pin have been extended (see pics# 4, 6, 9) to pick up attachments with a longer Pin Center spacing (full details below). Condition is Used, but is otherwise in good working condition with plenty of life left. Has Rear Lifting Eye Hook. *** Pin Setup Dimensions (where your Dipper Arm/Stick goes in): * Pin Diameter: 80mm. * Pin Center to Pin Center (

The price includes GST. New 80mm pin, 600mm Doherty Excavator Deep Trenching Cleanup Gummy Banana Bucket suit 15-32 ton machine. This is a thick & sturdy, well built bucket. The front cutting edge plate and Ear Plates are 32mm thick. Current Headstock configuration: 80mm Pin Diameter, 475mm Pin Center to Pin Center (CtoC), 336mm Between the inside Ear Bosses (which can be shaved back up to 356mm between the Ear Plates if you need more inside width for your hitch or dipper arm to fit in). Sho

The price includes GST. New 1200mm Excavator Skeleton Sieve Riddle Bucket suit 15-30 Ton machine. Front digging edge is 40mm thick and 300mm deep. Extra side cutter plates welded on. Current Headstock configuration: 80mm Pin Diameter, 452mm Pin Center to Pin Center (CtoC), 328mm Between the inside Ear Bosses (which can be shaved back up to 387mm between the Ear Plates if you need more inside width for your hitch or dipper arm to fit in). Should fit: Case 9021 / CX210 / CX210B / CX225SR, Cat

The price includes GST. New 1200mm Warrior Heavy Duty Excavator GP Digging Bucket suit 15-32 Ton machine. This is a very thick & sturdy, well built bucket. The front cutting edge plate is 40mm thick! It has a deep profile for a high capacity of 0.96 cubic meters. It has removable bolt-on Side Cutters. There are extra wear plates attached to the sides and also extra wear strips welded underneath for durability (see pic# 10). Current Headstock configuration: 80mm Pin Diameter, 460mm Pin Cent

The price includes GST. Used 450mm Wide Drum, Excavator Compaction Wheel suit 16-32 Ton machines. 4 rows of pads and fitted with dual Mud Scrapers between the pads. Conditions is used, it has a few bangs & dints but rolls smooth and has plenty of life left. This is a well engineered, heavy duty Compaction Wheel. Drum: * Width: 450mm. * Curved Steel Plate Diameter: 680mm (not including pads). * Total Drum Diameter (including pads): 780mm. Pads (tapered): * Height: 50mm. * Size at Top: 35mm w

The price includes GST. Used Jaws Excavator Hydraulic Coupler Quick Hitch to suit 20-35 Ton machines. Designed for Caterpillar 322/325/330 etc. but will fit other machines (see below list of machines we have found so far). Condition is used with a few bangs, scrapes and some wear around the pickup. It also has 2 cracks that will need welding (see pic# 10) and is priced accordingly. If we get a chance we will have these cracks repaired but will be relisting it for a higher price. Otherwise th

The price includes GST. 90mm/80mm pin Excavator Headstock to suit 17-36 ton machines. There is some surface rust and light pin wear but is otherwise in good condition. Can be used for a mounting headstock for a Rock Breaker Hammer or Auger, or mount as a regular headstock for buckets and other attachments etc. The 2 fins could be cut off to make a standard flat plate headstock. The 90mm Pin could be milled down in the middle to make an all-80mm pin headstock. Or the 80mm pin could be sleave

The price includes GST. Used 1250mm Excavator Flat Edge Blade Trenching Bucket suit 18-36 Ton machine. Condition is used but there is still plenty of life left. This is a good solid bucket with bolt-on side cutting edges & thick front edge cutting plate. There is also extra wear strips welded underneath for durability (see pic #10). There is a small tear near the rear of the left hand side (see pic #9) which can be easily welded up. Current Headstock configuration: Front Pin Diameter is 90mm

The price includes GST. New Doherty D-Lock Excavator Hydraulic Quick Hitch Coupling to suit 20-36 Ton machines. 90mm pin machine can pickup both 80mm & 90mm pin attachments! D-Lock Quick Coupler, Fully Automatic with Dual Pin Locking (no need to leave the cab to remove / re-insert the safety pin). This is a Multi Pin Center pickup hitch so it can grab buckets used on other machines with a 438mm-521mm Pin Center to Pin Center range. Very low profile & light weight. Lifting Eye rated: SWL 16,

The price includes GST. Used G-Tex Excavator Hydraulic Coupler Quick Hitch to suit 20-36 Ton machines. Designed for Komatsu PC300/PC340/PC350/PC360 etc. but will fit other machines (see below list of machines we have found so far). Condition is used with a few bangs and scrapes but is otherwise in good condition with plenty of life left. This is a quality built Hitch made in Australia by G-Tex. 90mm Pin Diameter. 513mm Pin Center to Pin Center (CtoC). Between The Ears (BTE): 340mm width whe

The price includes GST. 90mm pin, 750mm Titan Excavator GP & Trenching Bucket suit 22-40 ton machine. It has tapered sides so mud slides out easy and minimises ground resistance and there are extra wear strips welded underneath for durability (see pic# 10). The front cutting edge plate is 50mm thick! Condition is used but it has had very little use, with minimal wear on the teeth and almost no wear on the side cutting edges. This is a thick & sturdy, well built bucket, made in Australia by

The price includes GST. New 800mm AHE Excavator Digging & Trenching GP Bucket suit 15-40 Ton machine. This bucket is surplus stock from Atlas Heavy Engineering (AHE): https://ahe1.com.au. It has a deep profile and is in perfect New condition. It has removable bolt-on Side Cutters and is fitted with Genuine Caterpillar Teeth. There are also extra Wear Strips welded underneath for durability (see pic #10). The cutting edges of the sides of the bucket are 32mm thick. *** Current Headstock c

The price includes GST. Used, Solid & Deep, Heavy Duty Excavator Ripper, suit 20-50 Ton machine. Great for ripping up tree roots, breaking up rock and loosening rocky ground, tarmac, paved areas etc. It is used but still has plenty of life left. This is a seriously chunky Ripper with a solid Shank thickness of 100mm (see pics# 4 & 8). This Ripper has 100mm Diameter Pins which have been milled down in the middle to 90mm (see pics#9 & 10). They could easily be replaced back to normal 100mm pi