102 Results: New & Used in Parts & Accessories in Moolap 3224, VIC

2 new ones still sealed . Make sure you get the hubs like these as they are real hard to press the hub in later without damaging the bearings. For a j120 land cruiser and Prado 120 170 for both

new in box. never used, direct replacement,

I have a new 79-91 Porsche 928 aircon compressor, there are 2 styles of these, the pre 91 and 91 . This one will suit most, has the single v belt. Is pre oiled and ready for installation, I install a few of these in my 928 workshop. And can attest to these being really quite efficient and cold. I usually get bulk shipments from 928s-r-us and pelican parts,

cps crankshaft position sensor new and never fitted, ordered for a customer but found it was a more obvious problem before even fitting this

never used, the pump turns over slowly with 12v, so may need to be pulled apart and clean the contacts, but it does cycle.

From an 86 5.0 part no ******1021

X4 used Toyota Land Cruiser 200 series alloy wheels and BF Goodrich tyres. Approx 70% tread left Wheels are 5 spoke $900

My dad Just got an xr6 fg ute that had these on, he is going back to stock height. Should work on any falcon fg, maybe ba bf too but don't know

For a Vito, 2004ish to 2011 I think. That era anyway

Works well, went with different style

Near new, low km rebuild

Came from a low km rebuild, went fuel injection instead

I only have one of these

I have a set of front wheel bearings for a 66-69 Mustang. And probably all other Ford's of the era. These were in a wilwood brake kit, and I didn't need these as I have a 70 Mustang with slightly different sized bearings. Wilwood units are obviously pretty well built

I have some good condition front drums from my 70 mustang, no leaks and worked great. The 70-73 mustang all have the same bearing size. But the 64-69 have a smaller inner diameter of the bearing. I have those bearings if you want the earlier style. (I just bought a wilwood kit that was for an earlier mustang and had to get the 70 bearings to fit my larger spindle, otherwise it was a direct fit)comes with decent brake hoses, bearings from the 70. And if needed I can supply brand new 64-69 bearin

Right hand seat (American passenger) works well, and I'm sure just a re-skin will be suffice, frame is good, and latch and sliders work worry free. Has good bones for a re-skin or even just a bottom leather panel. Have another worse condition black drivers side for sale too, pictures of that attached. can do both for $180

I have 5 more new glow plugs that I got for my gl320, this should fit alot of the diesel 320 engines like cls320 ml320 and more, then I believe it is the same as jeeps and Chrysler engines too as they shared a few diesels (I believe the 300c) but please do your research. Price is for each one and includes postage

I have a great condition waterpump, came from a 69 mach 1 mustang Please check fitment

Bought from a wreckers with warranty but never ended up using it

This is from a 351c Cleveland in a 1970 mustang. I have confirmed the clutch latches when 12v is applied but I did not have a condenser to test. Spins smoothly. Should fit other vintage Ford's too. And I am only guessing it will fit a Windsor, not sure if it fits the 302 etc. Postage will be $25 extra

Have new stock standard size bearings, will fit in any 1grfe motor, still sealed

From a holden/opel astra, always had it spare but the car has since been sold. I verified it worked fine

I have a third gen camaro radiator spare, never used. It's for an auto (although you could just block the auto trans cooler or not connect it to suit manuals). This was for my 87 5.0, but pretty sure they are all the same,. And also fits firebird and trans am tooml. Can give you dimensions.

Great condition all working has lower tab broken as per photos other two no issues bolts in no problems hence the cheap price