334 Results: New & Used in Engine, Engine Parts & Transmission in Ipswich Region, QLD (Page 3 of 14)

New old stock "Hills Exhaust" tail pipe to suit XD Falcon sedan 4.9L V8. Part number - T2614 Please refer to photos of catalogue for correct fitment.

New old stock "Hills Exhaust" tail pipe to suit XD Falcon 6 cylinder station wagon. Part number - T2613

New old stock "Walker" tail pipe to suit XD Falcon Sedan 6 cylinder. Part number - T2612 Please refer to photos of exhaust catalogue for correct fitment.

New old stock "Hills Exhaust" tail pipe to suit XA & early XB Falcon sedan & coupe / hard top V8 & 6 Cylinder. Part number - T2413 Refer to photos of catalogue for correct fitment.

New old stock "Hills Exhaust" XA XB XC Falcon tail pipe to suit station wagon V8 & 6 Cylinder. Part number - T2570 Refer to photos of catalogue for correct fitment.

New old stock "Hills Exhaust" XA XB XC Falcon tail pipe to suit sedan & coupe / hard top V8 & 6 Cylinder. Part number - T2563 Refer to photos of catalogue for correct fitment.

Fully Reconditioned Unleaded 253 Blue Motor with Pre Pollution type Heads and 4brl Intake. 60 thou bore. Trimatic Pattern Block. Has mild Camshaft and Cometic Head Gaskets.. Really tuff 253. Located Tamborine QLD 4270 Rodney Delivery can be arranged

Selling some ford parts. Bonnet hinges $50 Strut tops $50 Mellings High Volume oil pump $50 Power master high torque starter $200 Horns heater and lsd are sold. Located in karalee QLD call o421429719

BRAND NEW 040 OVER SIZE PISTONS FOR A 2 LITRE PINTO ENGINE WITH GUDGEON PINS. NO RINGS OR CIRCLIPS SUPPLIED. CAN BE PICKED UP IN IPSWICH OR SENT WITH AUST POST AT BUYERS EXPENSE.

Good condition for Mercedes benz c200 turbo

2010 Proton Satria Neo auto Transmission. 78186Km

2010 Proton Satria Neo 1.6 S4PH engine. 78186Km

Purchased for my d series honda only to find out its for a b series. Packaging has been opened but the spring has never been used. Pickup redbank plains, qld or can post australia wide for an extra $5.

Selling maf sensor for gc8 wrx in working condition. Not needed

This item is a used original air cleaner to suit the two barrel carbs used on 253/4.2L Holden V8s. This is the early pre-pollution style as used on the HT, HG and early HQ models. I believe that it is from a HQ as the snorkel points towards the drivers front corner when mounted on the carb. Last photo shows a similar filter when fitted to a HQ 253. Please confirm fitment before purchase. [see photos] Air cleaner has light surface rust, but would come up great detailed with a new decal. There

Nissan navara d40 2012 euro map sensor for sale in good condition

Nissan navara d40 2012 euro map sensor for spain built original part in good condition

This item is a used original front exhaust header as used on HD and HR X2 and 186S models, HK, HT & HG 186S and LC & LJ GTR and XU1 Toranas. Please confirm fitment before purchase. [see photos] Header C has the connection for the choke pipe. This is model specific, so please check this before purchase. The header has been sandblasted, inspected and was free from repairs or damage before being coated in a quality high-temp "cast iron" finish. It then sat on the shelf in the shed for 5 years or l

BRACKET HAS HAD THE HEADS OF THE BOLTS WELDED TO MAKE IT EASIER TO BOLT IN TO THE CAR. THIS BRACKET SUITS THE ORIGINAL GIRLING BRAKE BOOSTER. IN EXCELLANT CONDITION FOR A 50 YEAR OLD PART. CAN BE PICKED UP IN IPSWICH OR SENT WITH AUST POST AT BUYERS EXPENSE.

THIS CROSSMEMBER HAS HAD A RUSTED IN BOLT ON ONE END TO HOLD THE LOWER CONTROL ARM ON. IT HAS BEEN BASHED OUT OF SHAPE TRYING TO GET IT OUT. CHECK THE PICTURE YOU WILL SEE THE ENLARGENDED HOLE AND THE TWISTED FRAME. IT REQUIRES HEATING UP WITH A OXY AND STRAIGHTENING BEFORE YOU CAN USE IT. NORMALLY SELL FOR ABOUT $400 IN GOOD CONDITION. CANBE BE SENT WITH AUST POST OR PAC AND SEND AT BUYERS COST.

THIS CAM HAS A BIT OF WEAR ON A COUPLE OF THE LOBES BUT IS STILL VERY USABLE. HAS ABOUT .380 LIFT ON THE LOBES. WOULD SUIT A CAR THAT HAS A MILD TUNE. IT HAS 293 STAMPED ON ONE END. CAN BE PICKED UP IN IPSWICH OR SENT WITH AUST POST AT BUYERS EXPENSE.

THIS IS A FACTORY SUPPLIED ITEM. MOST CORTINA GUYS NEVER KNEW IT WAS FITTED TO THE AUSTRALIAN GTs. ALL AUSTRALIAN MK1 GT AND GT 500 CORTINAS HAD THIS FITTED ON TOP OF THE TUNNELL UNDER THE CARPET TO HOLD THE CARPET UP TO THE CONSOLE. THE LOTUS AND OTHER ENGLISH CORTINAS HAVE A DIFFERENT FLOOR PAN AND TUNNELL THAT HAS A LUMP IN THE METAL FLOOR THAT FILLS THE GAP UNDER THE CONSOLE. IF YOU HAVE AN AUSTRALIAN GT WITHOUT THIS FIBREGLASS PART FITTED THE CARPET WILL SAG DOWN AND YOU CAN PUT YOUR HAND

THE GEAR LEVER WILL FIT ANY MK1 CORTINA WITH A MANUAL GEARBOX. THESE ARE A BIT HARD TO FIND THESE DAYS. I HAVE PULLED IT APART AND REPLACED THE NYLON PIVOT BALL WITH A STEEL ITEM. ALL BUSHES AND REVERSE PLATE CHECKED AND IN EXCELLANT CONDITION. THE GEAR LEVER HAS HAD A PIECE OF METAL WELDED IN TO EXTENT THE LENGTH ABOUT 40MM. CAN BE PICKED UP IN IPSWICH OR SENT AT BUYS EXPENSE WITH AUSTRALIA POST . I ESTIMATE THE FREIGHT TO BE BETWEEN $25 TO $30.

Now Building Ford 4ltr Barra Engines... Performance upgrades only please.. I use only the best parts and have a great deal of experience and knowledge to make your Barra Engine a long lasting and Bullet Proof combo.. I have got Blocks and Heads available or will do your old one.. $88 Hourly Rate inc gst.. Atomic Billet Oil Pump & Timing Chain ARP Head Stud's and Cometic Head Gasket Kelford Barra Valve Springs Port work to Head and Intake Rodney C Lee leesmechanical671@gmai