290 views
Holden 253 308 Downdraft EFI Stack Intake Manifold Complete Polished
$1,195 Negotiable
Holden 253 308 Downdraft EFI Stack Intake Manifold Complete Polished
You can call us on ******** 042 for all your enquires.
Engine Block Style: Stock/OEM standard deck
Injection Style: 8 Throttle body
Basic Operating RPM Range: Idle-7,000
Intake Trumpets: Intake Trumpets Included
EGR: No
Injectors Included: No
Fuel Rails Included: Yes
Throttle Body Included: 8 Pieces
Base Material: Aluminum Casting
Base Finish: Polished
Assembled: Assembled
Quantity: Sold as a Kit
The individual throttle body EFI system have all the flash of classic Weber induction but provide higher state of tune and engine performance versatility of EFI. Delivering crisp EFI performance with systems capable of supporting high hp. Fuel and air is delivered through precision cast aluminum 50mm IDA style throttle bodies that allow for superior idle characteristics and astounding throttle response while improving emissions and economy through tight air/fuel ratio control.
The linkage set incorporates the throttle stops, idle controls, lever arms and joiner/balancer all in one. It also features a single screw adjustment for calibrating front to rear throttle shafts.
The bell crank has a fully indexable eccentric cable pulley that enables good slow speed drivability and still attain full throttle geometry.
The throttle bodies have the following feature:
- CNC machined, Heat treated 601 Cast aluminum.
- Butterflies are measured for each bore & precision machined to a closer tolerance.
- Butterflies are secured to centerless ground brass shafts with split screws to ensure reliability and service ability.
- O-ring seals on lower mounting faces.
You can call us on ******** 042 for all your enquires.
Engine Block Style: Stock/OEM standard deck
Injection Style: 8 Throttle body
Basic Operating RPM Range: Idle-7,000
Intake Trumpets: Intake Trumpets Included
EGR: No
Injectors Included: No
Fuel Rails Included: Yes
Throttle Body Included: 8 Pieces
Base Material: Aluminum Casting
Base Finish: Polished
Assembled: Assembled
Quantity: Sold as a Kit
The individual throttle body EFI system have all the flash of classic Weber induction but provide higher state of tune and engine performance versatility of EFI. Delivering crisp EFI performance with systems capable of supporting high hp. Fuel and air is delivered through precision cast aluminum 50mm IDA style throttle bodies that allow for superior idle characteristics and astounding throttle response while improving emissions and economy through tight air/fuel ratio control.
The linkage set incorporates the throttle stops, idle controls, lever arms and joiner/balancer all in one. It also features a single screw adjustment for calibrating front to rear throttle shafts.
The bell crank has a fully indexable eccentric cable pulley that enables good slow speed drivability and still attain full throttle geometry.
The throttle bodies have the following feature:
- CNC machined, Heat treated 601 Cast aluminum.
- Butterflies are measured for each bore & precision machined to a closer tolerance.
- Butterflies are secured to centerless ground brass shafts with split screws to ensure reliability and service ability.
- O-ring seals on lower mounting faces.
- Date Listed:28/12/2023
- Last Edited:28/12/2023
- Condition:New
Similar Ads
- INLET INTAKE MANIFOLD GASKET KIT FOR HOLDEN HT HG HQ HJ HX HZ 4.2L 5.0INLET INTAKE MANIFOLD GASKET KIT FOR HOLDEN HT HG HQ HJ HX HZ 4.2L 253 5.0L 308$19Smithfield, NSW•89w
- Holden Commodore 253/308 Inlet ManifoldHolden 253/308 inlet manifold, great condition with almost no corrosion. CASTING NUMBER: 9947175 YEAR: 1988 MONTH: January Pick up preferred, can post if necessary Wetherill Park 2164$180Wetherill Park, NSW•43w
- HZ Holden 253 intake manifold with Stromberg CarburettorHZ Holden 253 2 Barrel intake manifold GM part number 9945690 with 2 Barrel WW Stromberg Carburettor GM part 23-3045 253 V8 HQ from July '71 to Oct '72. Cash on pickup from Northmead$230Northmead, NSW•1w
- Crane Cams Camshaft suit 253-304-308 HoldenCrane Cams #244521 is a hydraulic flat tappet camshaft that suits 253-304-308 Holden V8 engines from******1987. The camshaft has a smooyh idle in 308 engines, and a lope at idle in 253 engines, it has a broad power band and delivers excellent everyday street performance: Lobe seperation angle= 112 , Valve lift= 448 intake, 464 exhaust, Duration=268 intake, 276 exhaust. The cam is BRAND New and a genuine Crane Cams Camshaft.$390Maroubra, NSW•83w
- HOLDEN-COMMODORE-308-304-253-ENGINE-BLOCK-PATTERN-RE-DRILLS-TO-THolden/Commodore 308 / 304 or 253 Block Re-drills To Turbo or Trimatic Pattern This is not an add for a block This is to have your 308 / 304 or 253 block re-drilled Aussie 4 Speed/Tri-matic pattern To Turbo/350/400/700 or Power Glide Pattern OR Turbo/350/400/700 or Power Glide pattern To Tri-matic Pattern/Aussie 4 Speed WHICH EVER WAY YOU NEED IT. To drill a pattern change I need minimum of block and crank to set up on or I can do short blo$275Windsor, NSW•348w
- HQ HJ HZ HZ 253 Reco V8 EngineReco 253 V8 QR Prefix Aug 1977 date New ACL bearings all round New Dynotec cam 204@50” New Comp Cams lifters New Crow Cams pushrods New Hastings piston rings New JP timing chain New JP oil pump New GMB water pump New high volume mechanical fuel pump New electronic Bosch style dizzy, coil, leads & NGK spark plugs New sump Standard intake manifold Heads have been washed and leak tested Pistons have been washed and linished and are 060” flat tops Block is Trimatic pattern$4,000NegotiableCasula, NSW•3w
- Holden V8 253 308 Rocker Bridges Commodore Torana Monaro GTS StatesmanHolden V8 253 308 Rocker Bridge Commodore Statesman Torana Monaro SS GTS Photo is representative only as there is a quantity for sale all in good usable condition Pickup Campbelltown NSW or will post Australia wide with tracking for $10.60 NOTE ! I have 8 of these available.If you wish to purchase a quantity of bridges they can be shipped for the same cost as one.$19Leumeah, NSW•9w
- NEW STARTER MOTOR HOLDEN V8 253 304 308 5.0 HQ HX HZ VB VK VL VN VP VRSTARTER MOTOR FOR HOLDEN COMMODORE V8 VB, VC, VG, VH, VK, VL, WH, LH, LX, HQ, HZ, HG, HK, HT, HJ, VQ, VN, VR, VP, VQ, WB, CHECK TABLE BELOW FOR VEHICLES SUIT MAKE: HOLDEN MODEL: COMMODORE/KINGSWOOD,TORANA, VB, VC, VG, VH, VK, VL, WH, LH, LX, HQ, HZ, HG, HK, HT, HJ, VQ, VN, VR, VP, VQ, WB, YEAR: *****1995 ENGINE: 5LTR V8/ 253/308 ENGINE TRANSMISSION: AUTOMATIC FLANGE DIAMETER: 70 HOLES: 2 X 9.5 KW 1.7 LENGTH: 244mm$175Smithfield, NSW•72w
- Holden 253 308 engine builds GTS LC Torana Monaro HQ HZ HX HT HJ HKHolden 253 308 355 Engine Builds to suit your restoration, Street or Race Car, Burnouts, or Boat. Engine builder for 30 years. Competative pricing. Can build to suit your application. Can supply engine outright of build your own. Very competative freight pricing within Australia. Any questions please let me know.$1NegotiableOakville, NSW•23h
- Holden HK HT and HG 253 or 308 sumpSump to suit 253 308 in HK, HT or HG in good condition. No pick up at the moment but may have one soon.$400Merrylands, NSW•32w
- Coan Racing Turbo 400 Manual Valve Body Reverse Pattern PRN123 #22010Coan Racing Turbo 400 Manual Valve Body Reverse Pattern PRN123 #22010 TH400 Manual Valve Body Kit Components: - Valve body - Separator plate - Gaskets - Special manual valve - Modulator plug w/o-ring - Rear accumulator spring Coan Racing Manual Valve Bodies are for competition applications, they will provide full manual control over all shifts, and deliver without delay or time costly overlap. The manual vale body is used when the transbrake is not needed, such as bracket racing, tractor pull$795NegotiableCampbelltown, NSW•1w
- TH400 Turbo 400 Transmission Fully Reco with Stage 2 ShiftkitTH400 Turbo 400 Transmission Fully Reco with Stage 2 Shiftkit Please call for more information. For racing enthusiasts, our last shipment from the United States containing 150 mixed transmissions are being allocated. Secure your transmission today.$3,590NegotiableCampbelltown, NSW•3w
- Ford GT Falcon Top Loader Transmission NewFord GT Falcon Top Loader Transmission New Please call for more information. For racing enthusiasts, our last shipment from the United States containing 150 mixed transmissions are being allocated. Secure your transmission today.$2,590NegotiableCampbelltown, NSW•3w
You don't have any recently viewed items
Any items you have viewed recently will be displayed here
•••• ••• 0042