119 views
HOIST 4 Post Hoist 4 Ton Standard Part No.: S4PH4TONSTD Code No. 3
$4,049
Strutfit Pty Ltd Tel. No.: 03 – *****8322
Address : Unit 4, 6 Fowler Road, Dandenong South, Vic 3175
HOIST – 4 Post Hoist – 4 Ton Standard Part No.: S4PH4TONSTD Code No. 3
Code No.: 3
Part No.: S4PH4TONSTD
Shipping weight & size : 785 Kgs & 434*71*56 cm
Description :
PLEASE NOTE: THIS ITEM IS LOCATED AT OUR WERRIBEE WAREHOUSE AND IS AVAILABLE FOR PICKUP THERE ALTERNATIVELY IT CAN BE DELIVERED AT AN ADDITIONAL COST
INSTALLATION IS ALSO AVAILABLE AT AN ADDITIONAL COST.
Australia’s best selling 4 Post Hoist. Useful for working on cars and increasing storage space in your shed — It’s the perfect choice for commercial workshops and car enthusiasts alike.
4 Post Hoist Features
• 4000kg/ 4 ton safe load limit
• Lifting height of 1.9m
• A single hydraulic cylinder lifts the runways by pulling the cables
• Runways can be adjusted between two track settings by removing 4 bolts and sliding one over
• Keep your car off the ground away from being dented, scratched and touched
• Durable powder coated finish
Safety Features
• 4 point pneumatic safety lock releases
• Additional secondary safety lock when weight comes off the cables
• Runways must first be raised a fraction before the safety locks will operate to allow the car hoist to be lowered
• Heavy duty 6mm thick cross beams and 5mm thick runways
• 10mm steel wire rope equalising cables
• Anti-surge valve in the hydraulic power unit
What’s Included?
• 4 post hoist with all bolts, cables, lines and fixings
• 240V single phase hydraulic power unit
• Concrete anchor bolts
• Detailed installation instructions
What’s Not Included?
• Hydraulic oil
• Setup of power units electrical connection
• Compressed air supply
Optional Accessories
• A rolling Secondary Lift is the easiest way to jack up cars on the hoist
• An Optional Jacking Plate can be used as an extra support point under the vehicle
• Caster Wheels allow you to move the 4 Post Hoist around your workshop with ease
• Need to do wheel alignments? We offer a Wheel Alignment Kit as an add-on
• Storing cars above and below? Be sure to use our Oil Drip Trays to keep them safe
Shed Requirements
• 150mm deep concrete at 32mpa
• Minimum ceiling height of 3.5m
Warranty & Certifications
• 3 year Australian warranty* includes structure, hydraulics & electrics
• Australian WorkSafe registered design
• CE certification
MOTOR SPECS 240V 20A SINGLE PHASE
CLEARANCE BETWEEN POSTS 2715MM
MAX TABLE HEIGHT 1900MM
POST HEIGHT 2230MM
OVERALL WIDTH INCLUDING PUMP 3300MM
OVERALL LENGTH NOT INCLUDING RAMPS WHEN DOWN 4405MM
OVERALL LENGTH INCLUDING RAMPS WHEN DOWN 5165MM
TABLE LENGTH 4055MM
EACH TABLE WIDTH 480MM
N.W/ G.W 770KGS/ 785KGS
MINIMUM CONCRETE THICKNESS 150MM
Material Thickness
CABLES 10MM
CROSS BEAMS 6MM
RUNWAYS 5MM
COLUMNS 4MM
Freight Information
HOIST 434CM 71CM 56CM
TOTAL WEIGHT 785KG
Some of our items cannot be facilitated for pickups. This is because our items are located in different dispatch centres around the country and are shipped directly from these centres to our customers.
Items can be freighted at buyer's expense. Please specify when purchasing if you require quote on freight. Please provide (post code and suburb) so quote can be done or free pick up is offered.
Please ensure contact/payment within 3 days of purchase. If paying into my account or paypal, item will not be released till payment clears. Otherwise pick up within 7 days.
Address : Unit 4, 6 Fowler Road, Dandenong South, Vic 3175
HOIST – 4 Post Hoist – 4 Ton Standard Part No.: S4PH4TONSTD Code No. 3
Code No.: 3
Part No.: S4PH4TONSTD
Shipping weight & size : 785 Kgs & 434*71*56 cm
Description :
PLEASE NOTE: THIS ITEM IS LOCATED AT OUR WERRIBEE WAREHOUSE AND IS AVAILABLE FOR PICKUP THERE ALTERNATIVELY IT CAN BE DELIVERED AT AN ADDITIONAL COST
INSTALLATION IS ALSO AVAILABLE AT AN ADDITIONAL COST.
Australia’s best selling 4 Post Hoist. Useful for working on cars and increasing storage space in your shed — It’s the perfect choice for commercial workshops and car enthusiasts alike.
4 Post Hoist Features
• 4000kg/ 4 ton safe load limit
• Lifting height of 1.9m
• A single hydraulic cylinder lifts the runways by pulling the cables
• Runways can be adjusted between two track settings by removing 4 bolts and sliding one over
• Keep your car off the ground away from being dented, scratched and touched
• Durable powder coated finish
Safety Features
• 4 point pneumatic safety lock releases
• Additional secondary safety lock when weight comes off the cables
• Runways must first be raised a fraction before the safety locks will operate to allow the car hoist to be lowered
• Heavy duty 6mm thick cross beams and 5mm thick runways
• 10mm steel wire rope equalising cables
• Anti-surge valve in the hydraulic power unit
What’s Included?
• 4 post hoist with all bolts, cables, lines and fixings
• 240V single phase hydraulic power unit
• Concrete anchor bolts
• Detailed installation instructions
What’s Not Included?
• Hydraulic oil
• Setup of power units electrical connection
• Compressed air supply
Optional Accessories
• A rolling Secondary Lift is the easiest way to jack up cars on the hoist
• An Optional Jacking Plate can be used as an extra support point under the vehicle
• Caster Wheels allow you to move the 4 Post Hoist around your workshop with ease
• Need to do wheel alignments? We offer a Wheel Alignment Kit as an add-on
• Storing cars above and below? Be sure to use our Oil Drip Trays to keep them safe
Shed Requirements
• 150mm deep concrete at 32mpa
• Minimum ceiling height of 3.5m
Warranty & Certifications
• 3 year Australian warranty* includes structure, hydraulics & electrics
• Australian WorkSafe registered design
• CE certification
MOTOR SPECS 240V 20A SINGLE PHASE
CLEARANCE BETWEEN POSTS 2715MM
MAX TABLE HEIGHT 1900MM
POST HEIGHT 2230MM
OVERALL WIDTH INCLUDING PUMP 3300MM
OVERALL LENGTH NOT INCLUDING RAMPS WHEN DOWN 4405MM
OVERALL LENGTH INCLUDING RAMPS WHEN DOWN 5165MM
TABLE LENGTH 4055MM
EACH TABLE WIDTH 480MM
N.W/ G.W 770KGS/ 785KGS
MINIMUM CONCRETE THICKNESS 150MM
Material Thickness
CABLES 10MM
CROSS BEAMS 6MM
RUNWAYS 5MM
COLUMNS 4MM
Freight Information
HOIST 434CM 71CM 56CM
TOTAL WEIGHT 785KG
Some of our items cannot be facilitated for pickups. This is because our items are located in different dispatch centres around the country and are shipped directly from these centres to our customers.
Items can be freighted at buyer's expense. Please specify when purchasing if you require quote on freight. Please provide (post code and suburb) so quote can be done or free pick up is offered.
Please ensure contact/payment within 3 days of purchase. If paying into my account or paypal, item will not be released till payment clears. Otherwise pick up within 7 days.
- Date Listed:04/04/2024
- Last Edited:04/04/2024
- Condition:New
- Warranty:Yes
Similar Ads
- 6/8 Ton Bottle Jack Heavy Duty Hydraulic Lifting Ram Car Van BoatPlease order at https://ausmesepackaging.com.au/ 6Ton- $40 8Ton- $50 AS/NZS 6 8 TON Hydraulic Bottle Jack Car Truck Caravan Description: High quality bottle jack suitable for every day or occasional use. Very popular as a backup jack to carry around in 4x4's and vans etc. instead of the factory supplied jack. Long telescopic ram gives a greater lifting range than standard rams whilst keeping the overall minimum height down. Heavy duty cast base. With proper and regular maintena$40Dandenong South, VIC•90w
- Cargo Barrier for Toyota RAV4 2005 - 2018 modelsGenuine Toyota Cargo Barrier for Toyota RAV4. Toyota-supplied Ausguard brand. Suits 2005 - 2018 models. Barely used - excellent condition. Was taken off car immediately after purchase and kept in garage since. Comes with emergency escape hammer. Nuts / bolts not supplied but are cheap and easily available. Ausguard brand - product code A10/168, part no. 145M. Contact with any questions. Inspection welcome. Pickup Noble Park$350Noble Park, VIC•144w
- Dual Hitch Ball Mount Tow Bar Trailer 4WD Car Bike Rack Boat Multi UsePLEASE NOTE IT DOES NOT INCLUDE ANYTHING ELSE NO LOCKING PIN & NO 2" TOW BALL RECEIVER. AS IS NEW CONDITION, BUYERS BEWARE IT'S NOT PERFECT ALIGNMENT ITS SLIGHTLY OF CENTER SO PLEASE SEE PICTURES TO SHOW YOU WHICH WAY IT TILTS PLEASE.... THE LAST 5 PHOTOS ARE DEMOSTRATION PURPOSE ONLY! Suitable for standard 2” hitch receivers Heavy duty thick steel construction Multi-use:extra 2”x2”receiver allows you to mount a cargo carrier or bike rack at the same time Bouns hitch ball with 5000 lbs$125NegotiableKeysborough, VIC•205w
- RECARO SR-7 Reclining Sports SeatRECARO SR-7 SEAT Many in stock now, NO NEED to wait - https://www.ontherunmotorsports.com/products/recaro-sr-7-reclining-sports-seat Description The sports seat that brings sports & comfort into a good balance. The RECARO SR-7 belongs to the RECARO SR sports seat line-up that currently consists of 3 models, the SR-6, SR-7 and SR-11. All of them have the same seat structure, but each of these 3 models have a different approach: The RECARO SR-6 is the model focusing on perf$1,910Springvale, VIC•154w
- Recaro SR-6 Reclining Sports SeatRecaro SR-6 Reclining Sports Seat NO need to wait for weeks, most item in stock now, call us on 03-****8100 for your Recaro seat order now - https://www.ontherunmotorsports.com/collections/recaro/products/recaro-sr-6-reclining-sports-seat Recaro Japan SR-6 Reclining Seats (KK100S GK100S) Version (Side x Center) Color (Side x Center) Recaro SR-6 Reclining Sports Seat quantity Part Number: N/A Vehicles: Seats, Universal Brand: Recaro Japan Please note that products from$1,990Springvale, VIC•154w
- Car Security System Alarm Immobiliser Central Locking Shock SensorCar Security System Alarm Immobiliser Central Locking Shock Sensor 2 Remote * price not negotiable. ** Pick up (Doveton vic) or Postage on top. *** SMS only to 0-468 484 II 8 (try not to send msg on Gumtree Message as delay reply) check it out my other stuffs for sale. check the link below. https://www.gumtree.com.au/s-seller/GumtreeSeller/1023955440 Cheers. Overview: This alarm system is good for protecting all doors, boot and bonnet also to immobilise the vehicle. It$50Dandenong, VIC•29w
- POWERTECH Electrically Isolated POWER INVERTER 24V DCIt will deliver up to 400 watts of continuous power, while supplying surge currents up to a massive 1200 watts. DC input is through an 850mm lead with alligator clips. It features an inline 25A fuse and the output is a standard 3 pin mains socket. There is a rocker on/off switch, and LED indicators for power and fault. This unit also features fan assisted cooling. Typical Applications: Laptop computers, recharging power tools or batteries, lamps and fluorescents up to 400W, 54cm televisions$100NegotiableKeysborough, VIC•212w
- Chev pick-up 1960-62 fleetside lensesChev pick-up 1960-62 fleetside lenses Genuine NOS Delco Guide lenses. You are buying 2 lenses. Been on shelf many years. Pickup Warragul or Dandenong south area. Will post for $15$100Dandenong South, VIC•33w
- HSV HOLDEN VF GTS STEERING WHEEL R8 LSA MALOO SENATOR CALAIS SSVUP FOR SALE IS GENUINE HSV VF GTS LEATHER STEERING WHEEL COMPLETE WITH AIRBAG AND PEDALS VERY GOOD CONDITION CAME OUT OFF VERY LOW KMS VF GTS WITH 19,000KMS PICK UP IN DANDENONG NORTH OR HAPPY TO POST ANYWHERE IN AUSTRALIA FOR EXTRA COST. FITS ALL HOLDEN HSV VF GTS CLUBSPORT R8 LSA MALOO SENATOR CALAIS SS SV6 STORM UTE COMMODORE WAGON STATESMAN CAPRICE GRANGE SSV REDLINE Z SERIES THUNDER STORM BLACK EDITION. NO SWAPS CASH ONLY$750Dandenong North, VIC•14w
- Holden hsv vy clubsport cluster maloo senator calais r8 series 2Up for sale is a genuine hsv vy clubsport series 2 cluster good condition no broken clips and working 100% with 191,405kms lvl 3 part number*****0982 fits all vy calais Berlina storm ss Commodore hsv maloo senator gts coupe gto clubsport r8 sv8 monaro cv8 ute wagon Thunder executive lumina equipe 25th anniversary acclaim executive s pack. Pick up in Dandenong north or happy to post anywhere in Australia$850Dandenong North, VIC•3w
- 16mm BENCH DRILL OPTIMUM Quality Free Keyless Chuck Part No.: SDQ16 C4STRUTFIT PTY LTD - Tel. No.: 03 - *****8322 Address : Unit 4, 6 Fowler Road, Dandenong South, Vic 3175 BENCH DRILL PRESS Precision 16mm OPTIMUM Quality FREE Keyless Chuck Part No.: SDQ16 Code No. 4 Code No.: 4 Part No.: SDQ16 Shipping weight & size : 130 kgs & 145*65*45 cm Description: The OPTIMUM Precision Bench Drill Press is a highly accurate and reliable machine. The table is able to be rotated to make it capable of drilling a large range of angles. Another Quality OPTIMUM product!$750SHIPPING OFFEREDDandenong South, VIC•1h
- 30mm PEDESTAL DRILL PRESS 1100w 9 speed Part No.: SDQ30 Code 4STRUTFIT PTY LTD - Tel. No.: 03 - *****8322 Address : Unit 4, 6 Fowler Road, Dandenong South, Vic 3175 Website : strutfit.com.au Email : 30mm PEDESTAL DRILL PRESS OPTIMUM Quality Accuracy 1100w 9 Speed Wood Metal Part No.: SDQ30 Code No. 4 Code No.: 4 Part No.: SDQ30 Shipping weight & size : 130 kgs & 145*65*45 cm Description: The OPTIMUM SDQ32 Pedestal Drill Press is an extremely accurate and reliable Industrial machine for metal or wood work. The table is a$2,050SHIPPING OFFEREDDandenong South, VIC•1h
- 25mm PEDESTAL DRILL PRESS 750w 12 speed Part No.: SDQ25 Code 4STRUTFIT PTY LTD - Tel. No.: 03 - *****8322 Address : Unit 4, 6 Fowler Road, Dandenong South, Vic 3175 Website : strutfit.com.au Email : 25mm PEDESTAL DRILL PRESS OPTIMUM Quality Accuracy 750w 12 Speed Wood Metal Part No.: SDQ25 Code No. 4 Code No.: 4 Part No.: SDQ25 Shipping weight & size : 80 kgs & 140*55*45 cm Description: The OPTIMUM SDQ25 Pedestal Drill Press is an extremely accurate and reliable machine for metal or wood work. The table is able to be ro$1,550SHIPPING OFFEREDDandenong South, VIC•2h
You don't have any recently viewed items
Any items you have viewed recently will be displayed here
•••• ••• 8322