59 views
CAR HOIST 3 TON 4 POST NARROW Part No.: 4POST3TNARROW Code No.: 3
$3,849
SHIPPING OFFERED
Strutfit Pty Ltd - Tel. No.: 03 – *****8322
Address : Unit 4, 6 Fowler Road, Dandenong South, Vic 3175
CAR HOIST 3 TON 4 POST NARROW Part No.: 4POST3TNARROW Code No.: 3
Code No.: 3
Part No.: 4POST3NARROW
Shipping weight & size : 765 kgs & 438*71*56 cm
PLEASE NOTE: THIS ITEM IS LOCATED AT OUR WERRIBEE WAREHOUSE AND IS AVAILABLE FOR PICKUP THERE ALTERNATIVELY IT CAN BE DELIVERED AT AN ADDITIONAL COST
INSTALLATION IS ALSO AVAILABLE AT AN ADDITIONAL COST.
This narrow width 4 Post Hoist is the perfect car storage solution for home garages with limited space. This model is 378mm narrower than our 4 Ton Standard 4 Post Hoist, however all of the optional accessories remain compatible.
4 Post Hoist Features
3000kg/ 3 ton safe load limit
Lifting height of 1.9m
A single hydraulic cylinder lifts the runways by pulling the cables
Keep your car off the ground away from being dented, scratched and touched
Durable powder coated finish
Safety Features
4 point pneumatic safety lock releases
Additional secondary safety lock when weight comes off the cables
Runways must first be raised a fraction before the safety locks will operate to allow the car hoist to be lowered
Heavy duty 6mm thick cross beams and 5mm thick runways
10mm steel wire rope equalising cables
Anti-surge valve in the hydraulic power unit
What’s Included?
4 post hoist with all bolts, cables, lines and fixings
240V single phase hydraulic power unit
Concrete anchor bolts
Detailed installation instructions
What’s Not Included?
Hydraulic oil
Setup of power units electrical connection
Compressed air supply
Optional Accessories
A rolling Secondary Lift is the easiest way to jack up cars on the hoist
An Optional Jacking Plate can be used as an extra support point under the vehicle
Caster Wheels allow you to move the 4 Post Hoist around your workshop with ease
Need to do wheel alignments? We offer a Wheel Alignment Kit as an add-on
Storing cars above and below? Be sure to use our Oil Drip Trays to keep them safe
Shed Requirements
120mm deep concrete at 32mpa
Minimum ceiling height of 3.5m
Warranty & Certifications
3 year Australian warranty* includes structure, hydraulics & electrics
Australian WorkSafe registered design
CE certification
Specifications:-
MINIMUM CONCRETE THICKNESS
120MM 32MPA
MOTOR SPECS
240V 20A SINGLE PHASE
CLEARANCE BETWEEN POSTS
2337MM
MAX TABLE HEIGHT
1900MM
POST HEIGHT
2230MM
OVERALL WIDTH INCLUDING PUMP
2967MM
OVERALL LENGTH NOT INCLUDING RAMPS WHEN DOWN
4446MM
OVERALL LENGTH INCLUDING RAMPS WHEN DOWN
5206MM
TABLE LENGTH
4096MM
EACH TABLE WIDTH
480MM
N.W./ G.W
750KGS/ 765KGS
Material Thickness
CABLES
10MM
CROSS BEAMS
6MM
RUNWAYS
5MM
COLUMNS
4MM
Freight Information
HOIST
438CM
71CM
56CM
TOTAL WEIGHT
765KG
Some of our items cannot be facilitated for pickups. This is because our items are located in different dispatch centres around the country and are shipped directly from these centres to our customers.
Items can be freighted at buyer's expense. Please specify when purchasing if you require quote on freight. Please provide (post code and suburb) so quote can be done or free pick up is offered.
Please ensure contact/payment within 3 days of purchase. If paying into my account or paypal, item will not be released till payment clears. Otherwise pick up within 7 days,
Address : Unit 4, 6 Fowler Road, Dandenong South, Vic 3175
CAR HOIST 3 TON 4 POST NARROW Part No.: 4POST3TNARROW Code No.: 3
Code No.: 3
Part No.: 4POST3NARROW
Shipping weight & size : 765 kgs & 438*71*56 cm
PLEASE NOTE: THIS ITEM IS LOCATED AT OUR WERRIBEE WAREHOUSE AND IS AVAILABLE FOR PICKUP THERE ALTERNATIVELY IT CAN BE DELIVERED AT AN ADDITIONAL COST
INSTALLATION IS ALSO AVAILABLE AT AN ADDITIONAL COST.
This narrow width 4 Post Hoist is the perfect car storage solution for home garages with limited space. This model is 378mm narrower than our 4 Ton Standard 4 Post Hoist, however all of the optional accessories remain compatible.
4 Post Hoist Features
3000kg/ 3 ton safe load limit
Lifting height of 1.9m
A single hydraulic cylinder lifts the runways by pulling the cables
Keep your car off the ground away from being dented, scratched and touched
Durable powder coated finish
Safety Features
4 point pneumatic safety lock releases
Additional secondary safety lock when weight comes off the cables
Runways must first be raised a fraction before the safety locks will operate to allow the car hoist to be lowered
Heavy duty 6mm thick cross beams and 5mm thick runways
10mm steel wire rope equalising cables
Anti-surge valve in the hydraulic power unit
What’s Included?
4 post hoist with all bolts, cables, lines and fixings
240V single phase hydraulic power unit
Concrete anchor bolts
Detailed installation instructions
What’s Not Included?
Hydraulic oil
Setup of power units electrical connection
Compressed air supply
Optional Accessories
A rolling Secondary Lift is the easiest way to jack up cars on the hoist
An Optional Jacking Plate can be used as an extra support point under the vehicle
Caster Wheels allow you to move the 4 Post Hoist around your workshop with ease
Need to do wheel alignments? We offer a Wheel Alignment Kit as an add-on
Storing cars above and below? Be sure to use our Oil Drip Trays to keep them safe
Shed Requirements
120mm deep concrete at 32mpa
Minimum ceiling height of 3.5m
Warranty & Certifications
3 year Australian warranty* includes structure, hydraulics & electrics
Australian WorkSafe registered design
CE certification
Specifications:-
MINIMUM CONCRETE THICKNESS
120MM 32MPA
MOTOR SPECS
240V 20A SINGLE PHASE
CLEARANCE BETWEEN POSTS
2337MM
MAX TABLE HEIGHT
1900MM
POST HEIGHT
2230MM
OVERALL WIDTH INCLUDING PUMP
2967MM
OVERALL LENGTH NOT INCLUDING RAMPS WHEN DOWN
4446MM
OVERALL LENGTH INCLUDING RAMPS WHEN DOWN
5206MM
TABLE LENGTH
4096MM
EACH TABLE WIDTH
480MM
N.W./ G.W
750KGS/ 765KGS
Material Thickness
CABLES
10MM
CROSS BEAMS
6MM
RUNWAYS
5MM
COLUMNS
4MM
Freight Information
HOIST
438CM
71CM
56CM
TOTAL WEIGHT
765KG
Some of our items cannot be facilitated for pickups. This is because our items are located in different dispatch centres around the country and are shipped directly from these centres to our customers.
Items can be freighted at buyer's expense. Please specify when purchasing if you require quote on freight. Please provide (post code and suburb) so quote can be done or free pick up is offered.
Please ensure contact/payment within 3 days of purchase. If paying into my account or paypal, item will not be released till payment clears. Otherwise pick up within 7 days,
- Date Listed:04/04/2024
- Last Edited:04/04/2024
- Condition:New
- Shipping:Shipping & Pickup
Similar Ads
- Industry hoistIndustry hoist rated 1.5 ton can lift more the weight of this crane is 480 kg, very heavy will need appropriate trailer or tray truck, if interested please leave a message on and I'll call you back asap ps hoist is at carrum downs$200NegotiableMelbourne Region, VIC•2w
- Engine Crane 2 Ton Hydraulic Hoist Folding Shop Mobile Lifter Wor...2-ton lifting capacity Hydraulic Folding For storage Heavy-duty wheels Maximum Height: 2.5m Packing Dimension: Package A: 135x30x16cm, 49kg Package B: 70x50x9cm, 23kg HR23-DZ-178587$478.79SHIPPING OFFEREDMelbourne CBD, VIC•1w
- Millers Falls TWM Engine Leveller 1800kg (4000lb) Heavy DutyTake the time and effort out of aligning that heavy engine and transmission. The Millers Falls ELEV1800 1800kg Engine Leveller is a must-have for your workshop when you need to remove and replace a motor or line up heavy components around the workshop or garage. The Millers Falls ELEV1800 1800kg Engine Leveller features a threaded rod operated by a crank handle which allows fast & safealignment of heavy components, such as engines and transmissions, up to 1800kg by moving the suspension point$62Tottenham, VIC•89w
- Industrial 6:1 Saftey Factor Polyester Webbing Flat Lifting Sling 2plySuitable for use with cranes, hoists and blocks. Double ply 100% High tensile strength polyester, low elongation, with reinforced lifting eyes at each end Complies to EN1492-1:2000, colour-coded to meet international lifting standards, safety factor 6:1. Available for this listing, and price range from AUD35 to AUD228.0: Norminal Width Effective Length Working Loading Limit (WLL) 3"/75mm 3mtr 3 ton 4"/100mm 4mtr 4 ton 4"/100mm 6mtr 4 ton 6"/150mm 4mtr 6 ton 6"/150mm 6mtr 6 ton 6"/150mm 8mt$35Hoppers Crossing, VIC•246w
- OIL DRAINER 80 LITRE AIR UNDER HOIST CAR WORKSHOP TRUCKS WASTE OIWILL POST ANY WHERE IN AUSTRALIA FOR MORE INFO & POSTAGE COST, CONTACT STEVE o 4 o 1 o 4 55 08 CASH ON PICK UP BRAND NEW OIL DRAINER AIR 80 LITRE UNDER HOIST OIL DRAINER Steel fabricated 80 ltr reservoir and telescopic steel drain pan fitted with grid filter. Air discharge drain with hose. Fitted with reservoir oil level indicator tube. AUSTRALIA - WIDE DELIVERY AVAILABLE**************IMPORTANT************* FREIGHT COST MAY REQUIRE ADJUSTMENT FOR STATES LIKE SA, WA, NT AND REMOTE$199.99Bundoora, VIC•323w
- 6.4mm Borescope Pipe Endoscope Inspection Camera 5 IPS LCD 1080P 32GBCode: EY-355225176553 This item is **Free shipping** anywhere in Australia Metropolitan We don't ship to NT, WA or Remote areas. If you would to be sure, that item will it shipping to your area. Please message us before buying. Note: Pick-up is not available. Two-Way 180°Articulating: VEVOR endoscope adopts advanced 180-degree bi-directional steering technology, allowing the lens to rotate 180 degrees to the left and right. Enable you to examine areas from different angles and easily inspect$259SHIPPING OFFEREDDoncaster, VIC•2w
- CAR STANDS 6 TON EACH SILVER AXLE STAND LOW PRO TROLLEY JACK STANDSWILL POST ANY WHERE IN AUSTRALIA FOR MORE INFO & POSTAGE COST, CONTACT STEVE o 4 o 1 o 4 5 5 o 8 1 years WARRANTY BRAND NEW IN BOX PAIR OF RED COLOR PROFESSIONAL LIGHT WEIGHT CAR STANDS HEAVY DUTY 6Ton 6000KG CAN HOLD UP TO 6 TON EACH STAND SOLID STEEL CONSTRUCTION, SILVER COLOR. RATCHET LOCKING DESIGN, WITH SAFETY LOCKING PIN. MAXIUM HEIGHT 630MM MINUM HEIGHT 390MM NET WEIGHT 12KG ALSO PICK UP AND PAY FROM BUNDOORA 3083 AND CAN DELIVER IN LOCAL AREA$84.99Bundoora, VIC•323w
- 3 ton D shackle new never used $123 ton D shackle new never used minor surface rust Pick up Kilsyth Vic or post $12 No pay id bank transfer or cash$12SHIPPING OFFEREDCroydon, VIC•3w
- Brand New 3-Ton Low Profile Dual Pump Hydraulic JackBrand New 3-Ton Low Profile Dual Pump Hydraulic Jack Unleash the power of the Brand New 3-Ton Low Profile Dual Pump Hydraulic Jack! Swift and efficient, this jack is your go-to for quick and easy vehicle lifts. With a low-profile design and 3-ton capacity, it's perfect for any garage. Elevate your automotive projects with this durable and reliable tool – the ultimate choice for DIYers and professionals alike! We also have wide selection of tools: -Tool Storage Trolley's -Garage Equipments -G$219NegotiableSunshine West, VIC•22w
- New 3 Ton, 6 Ton Jack Stand, and 3 Ton Low Profile Hydraulic JackNew 3 Ton, 6 Ton Jack Stand, and 3 Ton Low Profile Hydraulic Jack 3 Ton Jack Stand $49 6 Ton Jack Stand $79 3 Ton Jack Steel $219 3 Ton Aluminium $279 **1 Year Standard Warranty** Order Now! Order Now! We also have wide selection of tools: -Tool Storage Trolley's -Garage Equipments -Garden and Outdoors -Hand Tools -Hydraulic Jacks -Pliers -Power Tools -Socket Sets -Sockets, Spanners & Tool Kits -Car Seats & Accessories For More Information: -----------Location------------ 5/556-598, Pri$49NegotiableDandenong North, VIC•56w
- METAL LATHE W/shop Bench METEX PRO 290x750mm 2 Axis DRO Part SMP290METAL LATHE Workshop Bench METEX PRO MP290 290x750mm 2 Axis DRO Part No.: SMP290 Code No. 4 Code No.: 4 Part No.: SMP290 Shipping weight & size : 229 kgs & 150*75*70 cm Description: The METEX PRO MP290 workshop metal lathe is unmatched in performance and affordability. When it comes to a metal lathe like the MP290, you’re getting a powerful 15ooW motor with speeds from 50-2,000 RPM, 2 axis DRO, 4 way tool post and much more. Check out the specifications below for the full details. Featur$7,050SHIPPING OFFEREDDandenong South, VIC•2h
- BELT SANDER LINISHER Disc Combo METEX 500 w W/Working Sand Pt SSMM4115STRUTFIT PTY LTD - Tel. No.: 03 - *****8322 Address : Unit 4, 6 Fowler Road, Dandenong South, Vic 3175 Website : strutfit.com.au Email : BELT SANDER LINISHER Disc Combo METEX 500 watt Wood Working Sanding Part No.: SSMM4115 Code No. 4 Code No.: 4 Part No.: SSMM4115 Shipping weight & size : 21 kgs & 56*32*28 cm Description: The METEX Belt Sander with 150mm Disc offers all the control and power you need for sanding smaller workpieces. Compact design is great for$350SHIPPING OFFEREDDandenong South, VIC•3h
- Waterproof DIAL INDICATOR 0-10mm Part No.: SDIALO Code No. 4STRUTFIT PTY LTD - Tel. No.: 03 - *****8322 Address : Unit 4, 6 Fowler Road, Dandenong South, Vic 3175 Website : strutfit.com.au Email : Waterproof DIAL INDICATOR 0-10mm Part No.: SDIALO Code No. 4 Code No.: 4 Part No.: SDIALO Shipping weight & size : 1 kgs & 20*10*5 cm Description: Waterproof precision dial indicators are designed for use with all magnetic bases. Great for measuring run-out on lathes, blades, mills, etc. Easy to read face features 0.01mm gradu$150SHIPPING OFFEREDDandenong South, VIC•3h
You don't have any recently viewed items
Any items you have viewed recently will be displayed here
•••• ••• 8322