462 views
Valvetone MK111 Impact Handwired Guitar Amp
$650
Please Note: You must text message or call if interested, no spam messages will be replied to!!
The Impact Mk III Amplifier Includes 2 x Spare Output tubes
The ValveTone Impact Mk III is an all-valve guitar amplifier with a clean power output of 2-watts. The Impact can be used at low volume
levels, without sacrificing tone. It is suitable for home practice, rehearsal and recording. The Impact uses a pair of NOS ( new-old-stock )
6F4P or 6DX8 output valves and a 12AX7 preamp valve. The 6F4P/6DX8 valves are only available as a NOS type - they are no longer
manufactured, but ample stocks are still available in Australia and overseas.
Impact amplifiers are hand-built, one at a time, using traditional point to point wiring techniques. Construction is on a diecast aluminium
box, with the external components exposed - a presentation unlike most other amplifiers.
The main front panel controls are Volume, Tone and Master. In addition there is a 3-position Gain switch and a 3-position Bright switch
These extra switches can be used with the main controls to create a wide tonal range, both clean and overdriven. There is also a
socket on the back panel labelled "FSW". A click-on click-off footswitch can be connected to this socket to produce a fixed amount of
gain boost. Note: A footswitch is not supplied with the amplifier.
Most effects pedals can be used successfully with Impact amplifiers.
An Impact amp will drive any guitar speaker box, from a single 6-inch speaker to a 4 x 12 quad. It can be used with any load impedance
from 4 to 16 ohms, but the optimum load is 8 ohms. Clean output power is 2 watts into 4 or 16 ohms, slightly more into an 8 ohm load.
The amplifier can be operated safely without a speaker. If there is no speaker plugged into the speaker socket, an internal resistor
becomes the amplifier load. This allows the line out socket to be used to drive a larger amplifier, or for a direct input to a mixing desk.
A 12AX7 preamplifier valve is supplied with the Impact, but any other valve in the 12A*7 family ( 12AT7, 12AU7, 12AY7, 5751 ) can be
used in this position - changing the valve type will alter the gain and may also change the tone. A spare set of 6F4P/6DX8 output valves
is supplied with each amplifier, because these are not as readily available as more standard audio types.
The Impact Mk III Amplifier Includes 2 x Spare Output tubes
The ValveTone Impact Mk III is an all-valve guitar amplifier with a clean power output of 2-watts. The Impact can be used at low volume
levels, without sacrificing tone. It is suitable for home practice, rehearsal and recording. The Impact uses a pair of NOS ( new-old-stock )
6F4P or 6DX8 output valves and a 12AX7 preamp valve. The 6F4P/6DX8 valves are only available as a NOS type - they are no longer
manufactured, but ample stocks are still available in Australia and overseas.
Impact amplifiers are hand-built, one at a time, using traditional point to point wiring techniques. Construction is on a diecast aluminium
box, with the external components exposed - a presentation unlike most other amplifiers.
The main front panel controls are Volume, Tone and Master. In addition there is a 3-position Gain switch and a 3-position Bright switch
These extra switches can be used with the main controls to create a wide tonal range, both clean and overdriven. There is also a
socket on the back panel labelled "FSW". A click-on click-off footswitch can be connected to this socket to produce a fixed amount of
gain boost. Note: A footswitch is not supplied with the amplifier.
Most effects pedals can be used successfully with Impact amplifiers.
An Impact amp will drive any guitar speaker box, from a single 6-inch speaker to a 4 x 12 quad. It can be used with any load impedance
from 4 to 16 ohms, but the optimum load is 8 ohms. Clean output power is 2 watts into 4 or 16 ohms, slightly more into an 8 ohm load.
The amplifier can be operated safely without a speaker. If there is no speaker plugged into the speaker socket, an internal resistor
becomes the amplifier load. This allows the line out socket to be used to drive a larger amplifier, or for a direct input to a mixing desk.
A 12AX7 preamplifier valve is supplied with the Impact, but any other valve in the 12A*7 family ( 12AT7, 12AU7, 12AY7, 5751 ) can be
used in this position - changing the valve type will alter the gain and may also change the tone. A spare set of 6F4P/6DX8 output valves
is supplied with each amplifier, because these are not as readily available as more standard audio types.
- Date Listed:28/11/2023
- Last Edited:23/04/2024
- Condition:Used
- Shipping:Pickup Only
Similar Ads
- 1990 Mesa Boogie Mark IV 3-Channel 85-Watt Guitar Amp HeadMint condition 1990 Mark IV amplifier in stellar condition, an amazing amp, an early Revision A MK IV head - serial number is pictured IV0598 - 598th Mark IV made. Dated inside on the chassis 9-18-90 which is 18th of September 1990 the build date, I can send a photo if interested in that. The amp is Australian mains voltage - 240v and its one of the best and most versatile Boogie amps ever made. The lead channel is definitely the highlight of the show. Insane high gain tones and screaming lead$5,250SHIPPING OFFEREDMalvern, SA•12w
- 1993 Mesa Boogie Mark IV 3-Channel 85-Watt Guitar Amp Head Revision AAmazing condition, made in 1993. Serial number is 5684 - pictured on the listing. An amazing amp, an early Revision A MK IV head. The amp is within the Australian mains voltage - 230v and its one of the best and most versatile Boogie amps ever made. Please note the Rhythm 1 Pull pot doesn't click when you pull it out. It stick functions as the pull bright when pulled and works, and then pushed back in goes to a darker sound. It just doesn't have the click feel to it. The pot still function as i$5,250SHIPPING OFFEREDMalvern, SA•12w
- Fender Blues Junior 111Modified BJ111. Upgraded output transformer from Evatco, 4,8,16 OHM impedance switch ( for adding a speaker cab )and the amp tech swapped out a capacitor for a hotter tone. The work was done years ago and she's given me no troubles since. Original transformer included. Apart from the tech fees, the transformer was $100 and switch $35. I'm interested in switching from Fender to Marshall as I've never owned a Marshall, so that's the reason for selling.$850Port Elliot, SA•2w
- 10W DIY valve guitar amp kit - great home workshop project!Building your own amp is a brilliant way for a guitarist to get in touch with the technology of valve amps. As well as deepening your understanding of tone and the inner workings of your amplifier, there is nothing like playing through an amplifier that you have constructed yourself! The DIY kit for the Lamington Lite includes all the parts necessary to build your own 10W valve guitar amp. You’ll simply need to supply some basic tools and you are on your way. The kit includes the very compreh$299SHIPPING OFFEREDAdelaide CBD, SA•52w
- Nux Frontline 50 Guitar AmpNux Frontline 50 Guitar Amp 2 channel with multiple sound options - built-in tuner in excellent condition$200NegotiableKapunda, SA•65w
- Line 6 Pod XT Pro rackmount guitar amp sim & multi-FXAn advanced member of Line 6's POD family, the POD XT Pro guitar effects processor delivers 32 groundbreaking amp models built from the award-winning technology found in the Vetta amp. It's also loaded with 22 cab and 4 mic models, 49 stompbox and studio effects, and 36 programmable channels. Extensive I/O includes XLR and 1/4" analog outs plus AES/EBU, S/PDIF, and USB digital I/O for ultra-deep computer-based patch editing. The programmable stereo effects loop opens up myriad possibilities for$300NegotiableMawson Lakes, SA•4w
- Guitar AmpVOX AC15 C1 Guitar Amp. Little Use and near new condition$750Wynn Vale, SA•3w
- Vox AC4C1-12 Tube Guitar AmpAC4C1-12 Classic - 4 Watt 1x12" Tube Combo Guitar Amplifier, famous for its ability to achieve classic VOX tone at low volume levels, the AC4 is one of the most popular amps in VOX s lineup. An ideal choice for the home or the studio, the AC4 Custom serves up an array of authentic VOX tone through a Celestion 12 speaker and can even be paired with external speaker cabinet for more tonal diversity. Amp is in excellent as new condition Contact Greg for details Free pickup and local delivery Aust$495SHIPPING OFFEREDAdelaide CBD, SA•13w
- Amp and guitar standVery sturdy hand made amp and guitar stand Good if you have limited room as can hold both amp and guitar Obviously amp and guitar not included in this sale Angled to best project sound from amp Pick up only from Golden Grove$45Golden Grove, SA•69w
- Fender Mustang I V2 20w Guitar AmpFender Mustang V2 20w Guitar Amp In excellent as new condition The second generation Fender Mustang I V2 20-watt 1 x 8″ modelling guitar combo amplifier features an amazing selection of modelled amplifiers including five new amplifier models such as ’57 Twin and ‘60s Thrift, 24 presets, and new effects including big fuzz, green screamer and intelligent pitch shifting. A built-in Chromatic tuner and USB Port are also standard. 20 Watt RMS output modelling electric guitar combo amplifier 1 x 8″$295SHIPPING OFFEREDAdelaide CBD, SA•5w
You don't have any recently viewed items
Any items you have viewed recently will be displayed here
•••• ••• 1770