121 views
CROW CAMS PERFORMANCE CAMSHAFT FOR HOLDEN BUICK L27 3.8L V6
$690
MACE ENGINEERING GROUP
CROW CAMS PERFORMANCE CAMSHAFT TO SUIT HOLDEN VN.II VP VQ VR BUICK L27 3.8L V6
Vehicle Fitment: Berlina VN.II VP VR, Calais VN.II VP VR, Caprice VR, Commodore VN.II VP VR, Statesman VQ VR
Part Numbers: CAM648, CAM682, CAM683
Please confirm which part number you require by utilising our vehicle fitment guide and parts guide in the above images. Applicable prices are mentioned next to the part numbers.
Stage 1 - CAM648
This Crow Cams very mild cam provides an exceptional torque curve. Given the powerband begins quite low in the rpm range, it has great towing capabilities and a strong pull off the lights. Valve-train doesn't require upgrading unless the motor will be exposed to constant heavy abuse. Expect gains of 15-20kW depending on your car's current configuration.
Stage 2 - CAM682
This Crow Cams performance based cam is designed for standard engines. It provides good mid-range power tailored for spirited street enthusiasts. A full exhaust system, cold air intake, valvetrain upgrade and tune post installation is recommended with this cam. Expect gains of 18-25kW depending on your car's current configuration.
Stage 3 - CAM683
This Crow Cams performance street/strip camshaft designed for modified engines. This cam was designed to squeeze the most out of your 3800cc Buick V6. To make full use of this cams capability, we recommend a light head work, a full exhaust system, cold air intake, valvetrain upgrade and tune post installation. Expect gains of 20-30kW depending on your car's current configuration.
Contents:
- 1 X Crow Cams High performance camshaft
Notes:
- Pushrod length will require checking if heads have been skimmed or block has been decked.
- Dyno tune is required post installation on stage 2 and 3 cams. In some cases we may be able to supply a tune to suit. Please refer to our cam and chip packages through another listing.
- We recommend dialing in all aftermarket cams using a degree wheel to ensure that they’re phased correctly with the crankshaft. You can do this by using our 8" or 11" degree wheel listed in another ad.
- Removing the timing cover may upset the sump gasket depending on certain models. We stock cork and metal sump gaskets if yours cannot be re-used.
- We have all gaskets available through other ads.
- The image is for illustrative purposes only.
***Please note that all items include free delivery Australia wide***
Contact us directly through Gumtree and we’ll be more than happy to help you out.
Alternatively, you can contact us on the following:
Website – maceengineering.com.au
Phone – ******** 223
Email – inf******@******.au
Terms of Warranty:
Customer must return the defective item(s) first, with a full description of the problem. Appropriate tests will be conducted to determine the authenticity of the defects and claims. Once, Mace Engineering Group is satisfied, identical item(s) will be sent out to the customer.
Customer must have at least 1 proof of purchase whether it is an invoice, confirmation of payment email or payment related receipt (paypal, bank statement, credit card statement, etc.)
G2953
CROW CAMS PERFORMANCE CAMSHAFT TO SUIT HOLDEN VN.II VP VQ VR BUICK L27 3.8L V6
Vehicle Fitment: Berlina VN.II VP VR, Calais VN.II VP VR, Caprice VR, Commodore VN.II VP VR, Statesman VQ VR
Part Numbers: CAM648, CAM682, CAM683
Please confirm which part number you require by utilising our vehicle fitment guide and parts guide in the above images. Applicable prices are mentioned next to the part numbers.
Stage 1 - CAM648
This Crow Cams very mild cam provides an exceptional torque curve. Given the powerband begins quite low in the rpm range, it has great towing capabilities and a strong pull off the lights. Valve-train doesn't require upgrading unless the motor will be exposed to constant heavy abuse. Expect gains of 15-20kW depending on your car's current configuration.
Stage 2 - CAM682
This Crow Cams performance based cam is designed for standard engines. It provides good mid-range power tailored for spirited street enthusiasts. A full exhaust system, cold air intake, valvetrain upgrade and tune post installation is recommended with this cam. Expect gains of 18-25kW depending on your car's current configuration.
Stage 3 - CAM683
This Crow Cams performance street/strip camshaft designed for modified engines. This cam was designed to squeeze the most out of your 3800cc Buick V6. To make full use of this cams capability, we recommend a light head work, a full exhaust system, cold air intake, valvetrain upgrade and tune post installation. Expect gains of 20-30kW depending on your car's current configuration.
Contents:
- 1 X Crow Cams High performance camshaft
Notes:
- Pushrod length will require checking if heads have been skimmed or block has been decked.
- Dyno tune is required post installation on stage 2 and 3 cams. In some cases we may be able to supply a tune to suit. Please refer to our cam and chip packages through another listing.
- We recommend dialing in all aftermarket cams using a degree wheel to ensure that they’re phased correctly with the crankshaft. You can do this by using our 8" or 11" degree wheel listed in another ad.
- Removing the timing cover may upset the sump gasket depending on certain models. We stock cork and metal sump gaskets if yours cannot be re-used.
- We have all gaskets available through other ads.
- The image is for illustrative purposes only.
***Please note that all items include free delivery Australia wide***
Contact us directly through Gumtree and we’ll be more than happy to help you out.
Alternatively, you can contact us on the following:
Website – maceengineering.com.au
Phone – ******** 223
Email – inf******@******.au
Terms of Warranty:
Customer must return the defective item(s) first, with a full description of the problem. Appropriate tests will be conducted to determine the authenticity of the defects and claims. Once, Mace Engineering Group is satisfied, identical item(s) will be sent out to the customer.
Customer must have at least 1 proof of purchase whether it is an invoice, confirmation of payment email or payment related receipt (paypal, bank statement, credit card statement, etc.)
G2953
- Date Listed:17/01/2023
- Last Edited:24/07/2023
- Condition:New
- Warranty:Yes
- Model:Other
- Make:Holden
Similar Ads
- Holden 308 Mild Engine Fully rebuilt suit Monaro GTS HK-HT HQ HJ HX HZHolden 308 Performance Engine Fully rebuilt suit Torana SLR LH LX Monaro GTS HK HG HT HQ HJ HX HZ Engine Rebuilt and ready to go Rotating Assembly fully Balanced from Flex-plate to Harmonic Balancer Block Honed New Rings Reground & Balanced 308 Crank New Oil Filter & OEM Holden Oil Pump New Brass Freeze Plug Kit New Cam Bearings New ACL Big-end / Conrod Bearings .030 New ACL Main Bearings .020 Resized Rods Holden Harmonic Balancer Holden Oil Pan suit HQ-HZ 10.0:1 Compression Ratio$5,950Essendon North, VIC•1w
- Holden 304, 308 355, LS Hydraulic Roller Lifters (Morel)Brand new Morel Hydraulic Roller lifters Purchased for holden 5 litre build, however will cover LS engines as well These lifters will fit VN (depending on camshaft) and VT blocks, as well as LS Only pulled one lifter out of packaging to test with cam in block (refer pic) Other than that these are NEW Had to change specification as cam changed Save some $ van post approx. $15 Australian wide Pics: 1. There is comparison between Morel HR lifter and GMH holden Hydraulic flat tappet lifter 2.$710Mount Martha, VIC•12w
- Fully 6 Bathurst spec 6 Cylinder Head 149,161,173,179,186, 202 HoldenHSD's Fully 6 lineup includes the Bathurst head. These heads are our fast road mainly set up for a solid cam application, using all the same cutters and hardware as our Fully 6 head so they are all using HSD's custom profiled 1.680 inlet and 1.440 exhaust valves, the exact same port sizing on the Inlet which is 37x58mm keeping the port size down to not slow down airspeed and keep as much torque in them as possible. These heads flow around 175 cfm@ .500" valve lift, at 28". (approx. 270hp pot$2,500Moorabbin, VIC•40w
- FORD 393 Stroker Cleveland engine 600hpFORD 393 Scat Stroker Cleveland engine 598.3 hp & 514.0 ftlb torque Complete New Engine Build & Dyno Tuned for Optimum Performance Block Torque Plate Honed .030 Block Surface Zero Deck Machine Block for 1 Piece Rear Main Seal Felpro 1 Piece Rear Main Seal ARP Main Stud Kit for Crank Scat 393 9000 Series 3.850 Stroker Crankshaft Scat H-Beam 6inch Rods & ARP Rod Bolts Flat Top Probe Pistons .030 Mahle Piston Rings low Tension Plasma Moly 1/16,1/16,3mm RM-0203 Romac Harmonic Balancer St$22,950Essendon North, VIC•1w
- Holden 186 street performace engineFor sale is an industrial S/H special 186 STD bore short motor OUTRIGHT SALE can fully reco it to a street cruiser includes boring honing crankshaft grind Quality pistons & Hastings rings Acl race bearings.Includes a FREE Crow cam either a 35666 or 35603 cam with alloy timing gears. All clearnces set & assembled. Worth over $4500 Please note images show finished product.$2,000Cheltenham, VIC•56w
- Crow Cams Superduty V8 Pushrods (PR-964-16), 253-308 standard lengthBought brand new and used for a few months in my car before I had to change the setup. Superduty .080" wall section pushrods, will suit a standard length Holden 253-308 application. These retail for about $220; I'm losing money as I had to go and buy another set, but make me an offer if you don't like the asking price. Can post easily.$180NegotiableClayton South, VIC•68w
- Crow cam for v8 5ltr vn vp vr vs. Brand new in box with all the bitsCrow cam for v8 5ltr vn vp vr vs. Brand new in box with all the bits and pieces.$900Pakenham, VIC•2w
- Bottom End Conversion Gasket Kit Holden CalaisV VF V8 L98 L77 6LBottom End Conversion Gasket Kit We also stock other parts for these vehicles. - Oil Pumps - Water Pumps - Top End VRS Gasket Kits - Conrod/Camshaft/Main bearings - Full Rebuild Sets - Crankshafts / Crankshaft seals - Cylinder heads and head bolts - Timing Chain kits - heaps of performance parts! Please message us for a OE or performance package and check out our other listings!! Item Grade OEM Standard Additional Package Contents Contains Miscellaneous Ga$125Hallam, VIC•95w
- HFM Sr20 Sr20det Forged 264 stage 2 Camshafts s13 180sx, 200sx, SilviaHFM Sr20 Sr20det Forged 264 Camshafts 180sx, Silvia Came off 180sx sr20 stage 2 cams Good for Datsun etc too 500$500Keilor Downs, VIC•28w
- Bmw s50b30 Euro Re-profiled CamshaftsI have some S50b30 (euro) reprofiled camshafts available. Brand-new condition. They were pre-profiled at Clive cams in VIC 293 duration intake and exhaust. 11.5 mm lift, can be run with or without VANOS. Haven't ever been run in yet so no scores or marks. Rookie purchase. Will not fit non-m heads. Hey, we are all learning. Have also done a runout check. All good. Around 0.001”$700Gembrook, VIC•37w
- 2 X BALL JOINT FOR TOYOTA BUICK L27 1GRFE 2GRFE 2GRFKS 3MZFE 5VZFE V6MACE ENGINEERING GROUP PAIR OF WASP BALL JOINTS TO SUIT TOYOTA BUICK LN3 L27 3VZ-E 3VZ-FE 1MZ-FE 3MZ-FE 5VZ-FE 1GR-FE 2GR-FE 2GR-FKS 3.0L 3.3L 3.4L 3.5L 3.8L 4.0L V6 Vehicle Fitment: 4Runner VZN130R, Aurion GSV40R GSV50R, Alphard MNH10R MNH15R, Avalon MCX10R, Camry VCV10R VDV10R MCV20R MCV36R GSV70R, Estima MCR30R MCR40R GSR50R GSR55R, FJ Cruiser, GSJ15R, Granvia VCH10R VCH16R, HiLux VZN130R VZN167R VZN172R GGN15R GGN25R GGN120R GGN125R, Harrier MCU10R MCU15R MCU35R, Kluger MCU28R GSU40R GSU45R$70Melbourne CBD, VIC•5w
- 2 X BALL JOINT FOR TOYOTA 5S-FE 3S-FE 3S-GE 3S-GTE 1GD-FTV 1KD-FTV I4MACE ENGINEERING GROUP PAIR OF WASP FRONT BALL JOINTS TO SUIT HOLDEN T1KZ-TE 2AZ-FE 2AR-FE 2AR-FXE A25A-FXS 5S-FE 3S-FE 3S-GE 3S-GTE 4A-FE 7A-FE 7A-FET 1ZZ-FE 2ZZ-GE M20A-FKS 2ZR-FXE 2ZR-FE 3ZR-FE 1NZ-FE 2NZ-FE 8NR-FTS 2Y 3Y 3Y-E 3Y-J 4Y 4Y-E 22R 1RZ-E 2RZ 2RZ-E 3RZ-FE L 2L 2L-T 2L-TE 3L 5L 5L-E 1TR-FE 2TR-FE 2KD-FTV 1GD-FTV 1KD-FTV 2GD-FTV 1NZ-FXE 1AZ-FE 2AD-FTV 2AD-FHV TURBO DIESEL 1.2L 1.3L 1.5L 1.6L 1.8L 2.0L 2.2L 2.4L 2.5L 2.7L 2.8L 3.0L I4 Vehicle Fitment: 4Runner YN63R LN61R RN130R YN130$56Melbourne CBD, VIC•5w
- BALL JOINTS FOR HOLDEN 307 327 253 308 350 LS1 L76 L98 304 STROKER V8MACE ENGINEERING GROUP PAIR OF WASP BALL JOINTS FOR HOLDEN LS1 L76 L98 33 308 350 STROKER 4.1L 5.0L 5.4L 5.7L 6.0L V8 Vehicle Fitment: Adventra VY VZ, Belmont HK HT HG HQ HJ HX, Brougham HK HT HG, Calais VK VL VN VP VS WH VZ, Caprice VS VQ WH WK WL, Commodore VB VC VH VK VL VN VG VP VT VT.II VU VX VY VZ, Crewman VY VZ, Gts HZ, Kingswood HK HT HG HQ HJ HX HZ WB, Monaro HK HT HG HQ HJ HX HZ V2 VZ, One Tonner HQ HJ HX HZ WB VY, Premier HK HT HG HQ HJ HX HZ, Statesman HQ HJ HX HZ WB VQ$60Melbourne CBD, VIC•5w
You don't have any recently viewed items
Any items you have viewed recently will be displayed here
•••• ••• 223