22 Results: New & Used in Engine, Engine Parts & Transmission in Mount Martha 3934, VIC

A Used Classic Mini Original Choke Cable (21A1202) fitted to the early Minis that used the single HS2 carby. Smooth in operation. Pay Pal accepted, will post $11.00

Classic Mini Cooper S Hardy Spicer Diff Output Shaft Special Bolt (22A1139) Genuine New Old Stock Quantity Three Available. PRICE SHOWN IS EACH.

Classic Cooper S Hardy Spicer Output Shaft Special Size Nut GFK3431 Genuine New Old Stock. Quantity Twelve Available PRICE SHOWN IS EACH.

Classic Mini 1275cc Primary Gear (22g1053) - Used A Primary Gear that is used with the stepped crankshaft (Pre A plus) in good used condition ,no gear wear or crumbling of the bronze bushes.

Mini 3 Syncro Gearbox Third Gear Thrust Washer. Genuine (2A3219) BMC Item

Classic Cooper S a used Original Smiths Petroflex Oil Cooler hose from the engine to oil cooler. Original Part No 13H3817 fitted to all Cooper S from 1966 onwards. After some 55 years hard to find these hoses in good condition,so please refer to photos showing the first signs of the outer rubber cover splitting which can easily be refixed.

Newish pushrods Only done 1500km Suit Chev 350 or holden Pending on you requirements Heavy wall 0.110” 5/16” dia 8” long Save $150 on new Can post $10 with tracking Only reason for selling need slightly longer

Brand new Morel Hydraulic Roller lifters Purchased for holden 5 litre build, however will cover LS engines as well These lifters will fit VN (depending on camshaft) and VT blocks, as well as LS Only pulled one lifter out of packaging to test with cam in block (refer pic) Other than that these are NEW Had to change specification as cam changed Save some $ van post approx. $15 Australian wide Pics: 1. There is comparison between Morel HR lifter and GMH holden Hydraulic flat tappet lifter 2.

NEW 5 pinion rear planetary carrier for 4L60, 4L60E 4L65E, 4L70E transmission, purchased for rebuild, but decided to change direction can post $20

NEW HIGH PERFORMANCE OUTPUT SHAFT To suit VR-VE holdens Purchased a month ago with other Sonnax stuff as know one had stock Not needed for my rebuild Completely new only taken out of box to take pic and to lather up with ATF Very nice piece made from 300M high alloy can with stand 1000hp same shaft is being used in all electronic 4 speed auto boxes from VR to VE holdens save yourself $250 on new output shaft Can post at your cost or pick up

Magnum air to go vehicle mounted air compressor Has been sitting around for years and was never used Feel free to come and take a look Pickup Mount Martha

Power Steering Pump for Holden Caprice Statesman VS

HOLDEN VS STATESMAN AIR BOX & Piping Duct Air Filter

Holden V6 engine cover VS VT VX VY

1995 HOLDEN VS STATESMAN OR COMMODORE V6 COIL PACK

Holden Commodore VS Air Bag Module ****8008

MOMO GEAR KNOB RRP$150 ... slight scratches from storage not fitted use ware. ALL QUESTIONS WELCOME

Gen IV sump, larger capacity 8/10 suit car/marine Been throughly cleaned and epoxy painted can post at your cost

New Edelbrock 2804: tall deck dominator $530 each Edelbrock 2803: standard deck dominator $600 SOLD

selling nice matching pair of Alum Bronze record props 16.5" Dia x 22" pitch cupped to suit a9 spline Arneson, Kaama or SSM3 drive nice condition can freight at your costs

Looking for Mercruiser trim pump complete with a broken / no working motor or minus motor complete 3 wire with solenoids Please ring and send pics of what you have Will pay postage Australia wife

Carrillo H-beam rods Standard bbc rods with the exception of length being 6.385” long instead of 6.135” ARP 2000 rod bolts There is some engraving on side of rod. 26907, brand of bolt total weight mains BE WMC bolts 807 579 228 Carr bolts 815 587 228 actual with ARP2000 bolts 824.5