1 Results: New & Used in Engine, Engine Parts & Transmission in Trigg 6029, WA

Commodore V6 3800 L67 Supercharged Pistons and Rings. Removed from a VX Series 2 engine. Used OEM standard bore genuine pistons in good condition. Minor scuffing to the skirt coating as expected. No damage and the ring grooves are not worn. All pistons have been measured at 3.7975" The pistons have been chemically cleaned and de-carboned, the pistons pins have been polished. Supplied with pin locks and a new set of standard bore Nippon Piston Rings. These where refurbished to be used and

Holden Commodore L67 4L60E 4 Speed Automatic Transmission Removed from a 1996 Supercharged VS V6 Commodore. Complete with torque convertor, transmission shifter and tailshaft (not pictured). I purchased the transmission bolted to a Supercharged V6 L67 and I was told that it was in good running order before being removed. I only require the engine as I am fitting a manual gearbox. I have removed the pan, it was clean and the oil was old but not burnt, there was no debris in the pan. I have fi

Genuine Borg and Beck Street Strip Clutch Pressure Plate or Clutch Cover. Manafactured by Borg and Beck in the USA for Hays clutches 11" diameter 3 finger with 12 heavy duty coil springs to maximize plate pressure. Assembled with roller assist to increase centrifugal clamp force with RPM. Suit Chevy Chev Chevrolet Buick Pontiac GMC etc. High performance usage. Used for a short time then removed. 3200 lbs static clamping force. Clean unmarked face. It has been boxed and protected since r

Chevy Cast iron Cylinder Head. "492 Double Bump Head". One (1) bare head only. Casting number 3991492 64cc combustion chamber and straight plug. Date code G61 G=July, 6=6th day, 1=1971 Over the counter performance GM cylinder with 2.02" and 1.60" valves, factory set up for screw in studs (7/16 thread) and guide plates with accessory holes. Standard 1.250" valve spring pockets. The head has been chemically cleaned and crack tested or NDT (magnafluxed). In excellent condition. NO port work or

Monaro GM 10 Bolt Diff Cover Plate or Back Plate. Suit a HK HT HG Monaro with Chevrolet / Chev 10 bolt differential. Original OEM Steel plate that has been chromed. The chrome finish is average. This is NOT a holden salisbury cover plate. $90.00 Ad removed when sold. If the ad is up then the cover is available. Tags : Chevrolet / Chev / Chevy

Genral Motors (GM) Clutch Release Bearing. New old stock part (NOS) GM part now discontinued. GM part number 1020356 Suits ZF 6 Speed gearbox GM fttment as listed below Fits 1989-91 L98 Fits 1992-93 LT1 Fits 1990-93 LT5/ZR1 Brand new in box. $110.00 Ad removed when sold. If the ad is up then the part is available.

HYDRA-CLUTCH Hydraulic Clutch Release Bearing Federal Mogul BCA Bearing Part number 619001 Suits Jeep Cherokee Wrangler Comanche YJ '87-'92 Brand new in box. $110.00 Ad removed when sold. If the ad is up then the unit is available.

Felpro Big Block Chev Gaskets Felpro 1605 x 2 sets Fel-Pro Performance Valve Cover Gasket Fel-Coprene Rubber Felpro x 1 pair 1410 Performance Exhaust Header Gasket Set 1.88" x 1.88" Suit Big Block Chevy Square Port. $80.00 Sold as a lot. Ad removed when sold. If the ad is up then the parts are available

Brand new filter sold car so not required

Holden HK HT HG Tail Shaft / Drive Shaft Power glide to 9 inch Ford diff This is a new drive shaft and it has never been used. As shown in the pictures manufactured by Hardy Spicer Belmont 40 years ago. Drive shaft has been in storage since. Shaft dimensions as follows : Length : Center uni to center uni 1425mm Diameter : 76.3mm (3.00") Cap diameter : 25.6mm Uni width : 81mm Yoke : To suit powerglide transmission. Pick up only. $450.00 Ad removed when sold. If the ad is up then the shaft is ava