11 Results: New & Used in Engine, Engine Parts & Transmission in Mildura Region, VIC

Brandnew never been taken out of packet selling it due to not needing it as to got another one with my thermostat and housing replacement

Ford falcon tail shaft from a XF falcon Ute. Was running behind a four speed gearbox

For sale is a four speed gear box removed from a XF falcon Ute. Only replaced as I fitted a 5 speed XG falcon

V8 Project. Made July 1976. Casting 27G6 for Holden HX. Engine number QR775099. Low mileage as seems on standard bore. Sale includes set of new pistons, STD Bore. Rods, Gasket kit, Crank, lifters, pushrods, Inlet Manifold, Cylinder heads, Camshaft and Oil pump. needs Tins: Rocker covers, Timing cover and a sump cover. Water pump and Thermostat. No time for this Project. Engine stand available $100. These are getting harder to find with a low mileage. Located in Mildura, Vic.

Fully rebuilt injection pump, was made to ' 30' to suit the turbo on my motor. Pump was built last July and has done approximately 17000ks, just over 3 services, of driving. Only reason for sale is going all out on the next 2h engine/pump/turbo setup and moving away from the inline pumps. Pump will be removed from engine in the next couple weeks when engine gets removed. Also have the injectors that were rebuilt with the pump that I would sell, $350 Also have a full set of injectors lines

Bought to replace the old STD size pistons, upon further inspection of the bores in my motor I've since decided to go all out on a ground up rebuild which in turn requires oversize pistons so these are also surplus to my needs. These are late model, short sleeve pistons with the steel insert in the top ringland to hold all the boost in. Comes with Japanese rings. Cost me 1150 to my door, quite firm on price Will trade for parts for a hj75, white rust free roof panel, rear windows panel,

Perkins 4 or 6 cylinder Diesel engine required Must be in good condition prefer marine accessories

this motor was taken out of our old Bond-wood Boat and replaced with a Holden Grey Motor in the mid 1960's. the Grey Motor was taken out of a rusted out old FJ Holden car, Father got at the time. so when the SIMCA Motor was taken out of the Bond-wood Boat, it was in a going condition, nothing wrong with it, no smoke, FINE. the problem was with the SIMCA Motor, just under power thing it was, to gutless to pull a water skier along at a good watering skiing speed. in all this time this SIMCA MOTOR

this 252 V6-CHEV MOTOR was brought in from the STATES, and has been re-worked. all machining work was done in Golden Square, Bendigo, by RACE MOTORS at the time. so all has been done there, and the motor has been in storage for many years now, never put back together. the 252 V6 Chev Motor is a 225 V6-Chev Motor, BUT fitted with bigger pistons, PUT in IT, and also to add here, a 225 V6-Chev Motor is say a 307 V8-Chev Motor, WITH 2 CYLINDERS CHOPPED OFF IT, to bring it back to 225 cubic inch mot

Ford or Holden fuel module. Fits variety of models. I bought it for a VS commodore but never used it. Still brand new in original packaging. Also have a crank angle sensor to suit V6 Ecotech engines still brand new. Also have brand new headlight to suit VY commodore ans VY dark tail lights look up my other adds for pics of lights. Also got VR VS white coloured doors abd a VR VS bonnet, find them in my other adds. Make an offer on any item or the whole lot. Check out all my adds

Spacer Flange brand new. I just took it out of the bag only to take photos to see clearly that it's new. I can post to you for extra $5.