218 Results: New & Used in Parts & Accessories in Maroubra 2035, NSW (Page 8 of 10)

Crower 68382 Dual Valve springs with damper for solid roller cams. The springs have an outside diameter of 1.450 in, Inside diameter of 0.705, and a spring rate of 436 lbs/in. This complete set of springs is brand new, and will fit any engine that the od and id fit, on a chevy small block street roller these springs shift the MAX RPM higher by 300. Genuine Crower.

Accel #77101 is a harness for Accels Dual sync Comp 9000 distributor, it plugs directly into the distributor plugs, and allows you to then join to your cars harness, all connections are lablled, brand new , genuine Accel.

Accel Comp 9000 dual sync distributor, part # 77190, has dual magnetic pick-ups that allows multi-port sequential operation as the ECU has two references for TDC on #1 cylinder, for Chevrolet small block 262-400 engines. It is constructed of billet aluminium, with upper and lower shaft bearings, it also has a very wide electrode spacing on the cap, so as to avoid crossfire. Beautifully machined, genuine Accel, brand new, and I have 2 available.

Moroso Pro Degree Wheel #62191 , is 18 inches in diameter, it allows much better accuracy due to its size when degreeeing camshafts. Made from aluminium, and comes with 3 bushings to adapt the centre hole to different size crankshaft/balancer bolts, brand new.

Crower 82020 High Rev Kit is for Chevrolet 262-400 engines, it allows you to mount a spring around the pushrod in the lifter valley, in doing so you keep the lifter on the lobe at high rpm, and you lower the amount the valve spring has to overcome also, it allows you to rev higher before experiencing valve float. Beautifully machined components, Crower Quality. Brand New.

Crower 66200 Roller lifters for Chevrolet 262-400 engines, these lifters are for a solid camshaft, they incorperate tie bars, beautifully machined from billet steel, Crower quality, and brand new.

Crower Street Roller Cam 00425, is a solid roller camshaft for Chevrolet 262-400 Chevrolet engines. Intake duration: 280, Lift .554, Exhaust duration: 288, Lift .567 , Lift based on 1.5 rocker ratio. Lobe seperation angle 112. Constructed of billet steel, machining is perfect, typical Crower quality, Brand New.

Crower 00550 Solid roller camshaft for Chevrolet 262-400 engines, it is designed for EFI Forced Induction and Nitrous. Intake duration:280 , Lift .547 , exhaust duration:288, Lift 573 , lift based on 1.5 ratio rocker, lobe seperation angle 114. Beutifully machined from billet steel, Genuine Crower, Brand new.

Moroso 85470 Breather tank can be used for coolant overflow or remote crankcase ventilation etc, it has a lower petcock for drainage, and comes with mounting bracket. Genuine Moroso, Brand new.

Fluidamper 712430 is designed for small block Chevrolet engines, it has a 71/4 inch diameter, and dampens from low rpm to high rpm, there is no specific range as the viscous fluid in the housing that supports the inner ring dampens at all rpm, it also has engraved timing marks, genuine Fluidamper, Brand new.

Milodon 12000 Pro Style Gear Drive for Chevrolet small block engines, it has a full cover design with a fixed idler gear so that timing NEVER CHANGES, as all gears are fixed, allows you to change your timing via multiple positions on the cam gear, superior to chan drives, looks cool too! Genuine Milodon, Brand new.

ARP 134-5403, Main stud kit for small block Chevrolet engines using a 2 bolt block, these studs have greater clamping than bolts, and will hold your main caps in their registers securely, comes with hex nuts. Genuine ARP, Brand new.

ARP 234-5601 Main Stud kit for Chevrolet small block engines with a 4 bolt main and are using a windage tray, the studs are slightly longer to accomodate the windage tray, these studs are the strongest and best quality you can get, far greater clamping load, thus a very solid bottom end, genuine ARP, Brand new.

ARP 234-4301 , 12 Point head stud kit for chevrolet small block engines, ARP studs are the best clamping you can get for your cylinder head, less distortion of your bore, and less chances of head gasket blowing under load, Genuine ARP, and Brand new.

Moroso 25800 Crankshaft wiper for small Block Chevrolet Engines, its constructed of steel, it bolts to the block using the oil pan bolts, you bolt it in without the sump and trim it as close as possible, so that the windage(when operational) is literally being scrapped/stripped from the crankshaft, thereby increasing horespower. Genuine Moroso, Brand new.

Milodon 32250 is a large windage tray for small block Chevrolet engines, it wraps around the crankshaft, and in its windows it has a mesh that has a diamond shape in its pattern, very effective at containing windage, it mounts to the main caps via mounting brackets that are on its underside, constructed of steel and plated for longevity, genuine Milodon, and Brand New.

Moroso 22112 Blueprinted Oil Pump for small block chevy, the tolerences between the pump gears and housing is a much closer, as is the end plate clearence. It has anti chatter grooves machined into the main body, so at high rpm you dont get erratic distributor movement, and there is also less foaming. The pump comes with a drive shaft and 2 springs in addition to the one in the pump, so you can fine tune your pressure. This pump is brand new.

Moroso 22167 Billet aluminium oil pump for chevrolet big block engines and small block engines, the pump is very light, and has a big mounting foot, with a lot of surface area. This pump is a gerotor pump so you get pressure at low rpm and high rpm with more consistency and no foaming. It has a built in pick-up, so fitment is faily easy, it comes with a drive shaft and spare spring which is for higher pressure, its held in position by a socket plug, easy to change. This pump is brand new.

Crower Billet Steel Connecting Rods for small block chevy engines, if you are using a blower or turbo these rods are a MUST. The rods are 6.0 inches in length, and fit a standard chevy main of 2.2250, they are capable of 1000hp , they are beautifully machined and all matching weights, a premium product from Crower, brand new!

This genuine MILODON PART# 11150 main cap conversion for chevy small block, it converts a 2 bolt main block to a 4 bolt main block, the new caps have angled fastners, as such they are stronger than a factory block, it comes with all fastners to do the job, after fitment you will need to hone the main bearing bore. This kit is brand new, and looks cool!

Crane Cams #244521 is a hydraulic flat tappet camshaft that suits 253-304-308 Holden V8 engines from******1987. The camshaft has a smooyh idle in 308 engines, and a lope at idle in 253 engines, it has a broad power band and delivers excellent everyday street performance: Lobe seperation angle= 112 , Valve lift= 448 intake, 464 exhaust, Duration=268 intake, 276 exhaust. The cam is BRAND New and a genuine Crane Cams Camshaft.

K=N racing Air Filter 60-1440 is a 14 inch diameter, and 7/8 inch dropped base, the element is cotton gauze and is 4 inches tall. In addition the air filter top is 60-1401 high flow top, which is also cotton gauze, the base and top flow serious CFM! Both are genuine K N , and are BRAND New!

MSD 8514 is a billet aluminium oil plug/camsync for small block Chevrolet engines, it allows a computer to know when the number 1 cylinder is at TDC so as to enable sequential injection, it also has a billet lower gear so it can be used with roller cams. It take the place of the distributor, so all oiling can continue as it did, this cam/sync plug is genuine MSD and is BRAND new, makes it easy to get EFI on a small block! I have 1 available.

Pacemaker competition headers #PH5325 , with Flowmaster scavenge collectors, primary pipe 1 3/4, Collector 3.0 inch, it is also fitted with a Vac-u -Pan valve on each collector, each header is fitted with a 316 stainless steel heat sheild that is polished, comes with a sandwich transmission mount that mates to the two tabs on each collector, finnished in black ceramic paint, these are competition headers and will fit HQ-WB Holden, and Chevrolet Corvette 80-81(message me for specific fitting),