8 Results: New & Used in want job in Australia

• Mercury

I have these two Mercury racing propeller, right hand and left hand, size is 17.5 x 29, models are G294R and a G293L. They owe me $2000.00 from a job which I did many years ago. I can supply the history for you, I can arrange to post or I can deliver to Sunshine coast or Gold Coast regions. Anyway if you want better photos I can supply. ( give me an offer that is reasonable just to try and recover some of the costs)

• Single Hull
• Other

Bellboy Yellowtail 5m half cabin boat. Fiberglass hull, in good solid condition, paint job could do with a sand back and paint. Was planning on doing this but don't have the time, let alone take her out fishing! * Suzuki 60hp motor 300 hours serviced last year with impella replaced (really good condition) * Electronic fuel injection * Hydrolic steering * Solid transom * New floor and carpet * 2 New seats * Dual batteries * Anchor winch * Boat catch * Bimini with rocket launchers (folds down)

• 14 ft

4.35M Stacer Custom Boat was originally a front console converted into a tiller steer, have not had the time to use it properly for about a year but has been started every few months and flushed. 2002 40HP Mercury in excellent condition. Completely rebuilt in 2014. New gearbox seals, oil, impeller 6 months ago. Custom electric tilt/trim on the end of the tiller shaft. Key start on side console. Boat has a fresh 12 months rego but the trailer currently needs a blue slip, will have fresh 12 mon

• Seafarer

Ok all due to a medical condition I can no longer do the couple of small jobs I wanted to do plus giving it a good tidy up so I’m very negotiable on price. Please no low ball offers if you do don’t be offended by my response. I need it gone. Want it gone open to serious offers not stupid ones. Time to sell me boat. It’s a Lindsay Fry built 595 seafarer victory 1995. Has 150hp Yamaha four stroke with 1270 hrs. Has new seats fitted. Comes with a 585 furuno sounder 1kw transducer great for out w

• Single Hull
• 18 ft
• Flight Craft

- 18ft australian flightcraft ski boat - Fully custom built 12 months ago - Immacualte condition and perfect working order - ENGINE - Just serviced - Rebuilt 350 chev midnount engine(sounds and runs amazing!) - Rebuilt & jetted holley 650 carbs - Brand new MSD distributer/inbuilt coil - Brand new water pump - New belts - New hoses - New bilge pump - New wiring loom/heat protected - New temp sender - LED digital gauges - New throttle system (telescopic shaft instead of cable)(new brackets and m

• Single Hull
• 14 ft
• Other

For Sale Marine ply Punt/Air boat hull 15 ft 6" long, 6ft wide and 1ft 6" deep, it has a casting deck and is very strong, with well over $2,000 worth of fibre glass gear to finish the job, every thing you will need and more. A great project for some one to finish, only selling because i haven't the time or the health, well priced, This price doesn't include the trailer, so if you want a trailer i am willing to sell it for what it would cost me to get a used one $855.00.

• 8 ft

Authorised Lite Kit for the Joey Wooden Dinghy from Boatcraft Pacific. Includes plans plus plywood components required to build a stitch and glue Boatcraft Pacific "Joey" row/sail dinghy. Epoxy, paint etc can be purchased separately from Boatcraft Pacific agents. Pick-up only, from Ivanhoe, Vic. Cut from 4mm BBA grade plywood. I have built this exact model boat and used it for 10 years as a tender and for pleasure. It is a great design - quick, stable, robust. Has a great payload capacity of

• Single Hull
• 30 ft
• Hatteras

Up For Sale: ( Will also swap for a pontoon/BBQ boat) • Custom Hatteras 30FT Boat 1986 model • 2X 200 Yamaha 2003 model Outboards, sequenced serial #’s and left/right rotation • 75% refurbished still need a tiny bit of work. The right person can finish it off just perfect • Brand new 9” SIMRAD sounder that was barely used but was kept updated, Transducer is attached at the rear of the boat • New marine suede for the front birth sleeping/seating section when it finished the first round