248 Results: New & Used in Engine, Engine Parts & Transmission in Campbelltown 2560, NSW (Page 10 of 11)

Chevy GM LS7 Downdraft EFI Stack Intake Manifold System Satin You can call us on for all your enquires. Engine Block Style: LS7 Injection Style: Individual Downdraft Throttle Bodies Basic Operating RPM Range: Idle-7500 RPM Intake Trumpets: Intake Trumpets Included EGR: No Injectors Included: No Fuel Rails Included: Yes Throttle Body Included: 8 Pieces Base Material: Aluminum Casting Base Finish: Satin Assembled: Comes Non-Assembled Quantity: Sold as a Kit. Notes: Check Applicatio

Holden 253 308 Downdraft EFI Stack Intake Manifold Complete Polished You can call us on for all your enquires. Engine Block Style: Stock/OEM standard deck Injection Style: 8 Throttle body Basic Operating RPM Range: Idle-7,000 Intake Trumpets: Intake Trumpets Included EGR: No Injectors Included: No Fuel Rails Included: Yes Throttle Body Included: 8 Pieces Base Material: Aluminum Casting Base Finish: Polished Assembled: Assembled Quantity: Sold as a Kit The individual throttle bod

Chevy SBC 350 0.842 Inch Retro Fit Solid Mechanical Roller Lifters #PC2957 Please call for more information.

Here we have an Igniter Module to suit a Toyota Celica ST162 . This has been tagged and stored , This is in used condition and will just need a clean before fitting . It will fit******1988 and 1989 models . I have other early Toyota parts I will list as I empty the shed. It has been stored in a shed for over 15 years and it's just time to get rid of all the hoarded parts I have collected as it’s just out of control. I will assist with postage at your cost if needed.

Chevy SBC 350 3.75" 383ci 1Pc RMS Stroker Rotating Assembly Kit (C,H 5.7,H 30) Please call for more information. Actual Engine CID: 383 Bore (in): 4.030 in. Engine Stroke (in): 3.750 in. Balanced: No Pistons Included: Yes Piston Rings Included: Yes Piston and Ring Oversize (in): 0.030 in. Piston Material: Hypereutectic aluminum Piston Style: Flat top, with four valve reliefs Piston Head Volume (cc): -4.00cc Wrist Pin Style: Floating Piston Ring Facing Material: Pla

Chevy LS2 4.005" 413ci Forged Stroker Rotating Assembly Kit (F,H,F) Please call for more information. Actual Engine CID: 413 Bore (in): 4.000 in. Engine Stroke (in): 4.100 in. Balanced: No Pistons Included: Yes Piston Rings Included: No Piston and Ring Oversize (in): 0.030 in. Piston Material: Forged Piston Style: Flat top, with two valve reliefs Piston Head Volume (cc): -4.00cc Wrist Pin Style: Press-fit or floating Piston Ring Facing Material: N/A Crankshaft Inclu

Chevy LS3 4.070" 427ci Forged Stroker Rotating Assembly Kit (F,H,F) Please call for more information. Actual Engine CID: 427 Bore (in): 4.070 in. Engine Stroke (in): 4.100 in. Balanced: No Pistons Included: Yes Piston Rings Included: No Piston and Ring Oversize (in): 0.005 in. Piston Material: Forged Piston Style: Flat top, with two valve reliefs Piston Head Volume (cc): -4.00cc Wrist Pin Style: Press-fit or floating Piston Ring Facing Material: N/A Crankshaft Inclu

Ford 351W Windsor 3.850" 393ci Stroker Rotating Assembly Kit (C,H,H 30) Please call for more information. Actual Engine CID: 393 Bore (in): 4.030 in. Engine Stroke (in): 3.850 in. Balanced: No Pistons Included: Yes Piston Rings Included: Yes Piston and Ring Oversize (in): 0.030 in. Piston Material: Hypereutectic aluminum Piston Style: Flat top, with four valve reliefs Piston Head Volume (cc): -4.00cc Wrist Pin Style: Floating Piston Ring Facing Material: Plasma-moly

Mass air flow sensor brand new unused 22204-22010 generic fit 02 Wrx and Toyota and more call Dan

K&n air filter 33-2232 fit Wrx 02 brand new still sealed call Dan

4 x spark plugs unused Ngk laser platinum pfr7b 4853 call Dan

Here we have a GM Stromberg Varajet 2 Carburettor for a WB or Commodore VC or VH . This looks to be complete and I suppose it will need a kit put through it as seen in the photos and it will need a good clean up . To suit a******1981 1982 and 1983 model . I have other early Holden parts I will list as I empty the shed. It has been stored in a shed for over 15 years and it's just time to get rid of all the hoarded parts I have collected as it’s just out of control. I will assist with postage

unbreakable copper head gasket to suit turbo conversion or big boost high performance rebuild, approximately 2.8mm thick.

full set of VVT (lost motion assembly rocker) springs. if the engine sounds like it has a tapping noise like a bad vslve lifter, it may have broken a LMA spring in the VVT rocker. These need replacing in 1.8L civic engine after 150k or risk destroying the whole cylinder head. very easy to install with a basic 10mm ratchet spanner/shifter and a magnet to collect any broken parts. contact us, we can also supply them in singles if you don't need the full set. pride includes express shipping.

Brand new, various spark plugs.

Ford au 6 cylinder fuel rail with stock injectors and injector plugs

Ford el ef radiator good condition

Super high quality Japanese Ganador cat back. Beautiful sound. Two oval mufflers. Came off r33 gtr, probably fit gtst and whatever else.

Brand new in box 8685 gen2. 1.28 v band rear housing. Changing direction with build. Suit rb26, 2jz, 13b, 20b, gtst, gtr, supra, vl, rx7 etc. Replacement price with vband rear is over 7k. Negotiable price

So you can put a Holden engine in make an offer

Hks 2860 turbo Bearings are shot needs rebuild $100 Turbosmart supersonic bov $50

Rb26 cam covers painted gloss black with big breather fittings welded. R34 centre cover with tomei badge. All in good condition suit gtr gtst anything rb swapped

Crisp mods EGR delete kit. Removed from Mitsubishi Triton MQ 2.4 4N15 diesal turbo 07/2017. What vehicles does this suit? 2015 - Current MQ Triton - 4N15 2.4L Engine Fiat Fullback (4N15 HP) 2016 - Current Pajero Sport - 4N15 2.4L Engine https://munji.com.au/products/egr-delete-kit-mitsubish-4n15-engine-triton-mq

Exedy clutch kit NSK-6331. For Nissan CA20 Engines.